Komatsu PC500LC-10R Скачать руководство пользователя страница 464 | Manualshive

Страница: 464 / 758

Komatsu PC500LC-10R Скачать руководство пользователя страница 464

UNDERCARRIAGE AND FRAME

TEST AND ADJUST TRACK TENSION

Tools for testing track tension

Symbol

Part No.

Part name

Q'ty

Remarks

A

Commercially

available

Wooden block

1

k

Place the machine on a level ground, lower the work equipment to the ground so that it is stable, set

the lock lever to LOCK position, and stop the engine.

For testing and adjusting the tension of track shoe to perform troubleshooting, refer to this section.

METHOD FOR TESTING TRACK TENSION

1.

Turn the fuel control dial to MIN (Low idle) position. Drive the machine forward by the length of track on
ground. Then slowly stop the machine.

2.

Put a bar A on the track shoe between the idler and the
first carrier roller.

REMARK

Use an L shape steel bar, etc. with lesser deflection for the
square bar A.

3.

Measure the maximum clearance (a) between the square
bar A and the track shoe.
Standard max. clearance (a): 16 to 34 mm

METHOD FOR ADJUSTING TRACK TENSION

Adjust the track shoe tension according to the following procedure when it is abnormal.

How to increase the tension

1.

Pump in the grease through the grease fitting (1) by using
a grease gun.

2.

Check that the tension is correct. Run the engine with the
fuel control dial at MIN (low idle) position, and move the
machine slowly forward by length of track on ground, then
stop the machine.

3.

Check that the tension is correct again according to the
above procedure after finishing adjustment.

NOTICE
The grease can be pumped in until dimension (b) be-
tween the idler guide and the track frame end becomes
0 mm. If the tension is still loose, the wear of pins and
bushings is large. In such a case, the pins and bush-
ings need to be turned 180 deg. or replaced.

TEST AND ADJUST TRACK TENSION

30 TESTING AND ADJUSTING

30-58

PC500LC-10R

«
...
462
463
464
465
466
...
»

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов