manualshive.com logo in svg

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 382 / 758

Поделиться
Скачать
Komatsu PC500LC-10R Скачать руководство пользователя страница 382

Abbrevia-

tion

Actual word spelled out

Purpose of use (major ap-

plicable machine (*1), or

component/system)

Explanation

MMS

Multimedia Messaging
Service

Communication

This is a service that allows transmission and re-
ception of short messages consisting of charac-
ters or voice or images between cell phones.

NC

Normally Closed

Electrical system, hydraulic
system

This is a characteristic of electrical or hydraulic
circuits. Circuit is normally closed if it is not actu-
ated, and it opens when it is actuated.

NO

Normally Open

Electrical system, hydraulic
system

This is a characteristic of electrical or hydraulic
circuits. Circuit is normally open if it is not actuat-
ed, and it closes when it is actuated.

OLSS

Open-center Load
Sensing System

Hydraulic system

This is a hydraulic system that can operate multi-
ple actuators at the same time regardless of the
load.

PC

Pressure Compensation Hydraulic system

This is a function that corrects the oil pressure.

PCCS

Palm command control
system

Steering

This is a function that electrically controls the en-
gine and transmission in an optimal way with the
controller instantly analyzing data from levers,
pedals, and dials.

(D Series)

PCV

Pre-stroke Control Valve Engine

This is a valve that adjusts the fuel intake amount
at the pump inlet in order to control fuel dis-
charged volume of supply pump.

PPC

Proportional Pressure
Control

Hydraulic system

This is a system that operates actuators in pro-
portion to the oil pressure.

PPM

Piston Pump and Motor

Hydraulic system

Piston type hydraulic pump and motor.

(D, PC, etc)

PTO

Power Take Off

Power train system

Power take-off mechanism

PTP

Power Tilt and power
Pitch dozer

Work equipment

This is a function that performs hydraulic control
of the tilt and pitch of the dozer blade of the bull-
dozer.

(D Series)

ROPS

Roll-Over Protective
Structure

Cab and canopy

ROPS is a protective structure that intended to
protect the operator wearing seat belt from suffer-
ing injury which may be caused if the cab is
crushed when the machine rolls over. (Roll-over
protective structure)

This performance is standardized as ISO 3471 or
ISO 12117-2.

SCR

Selective Catalytic Re-
duction

Urea SCR system

This is an exhaust gas purifier using urea water
that converts nitrogen oxides (NOx) into harm-
less nitrogen and water by oxidation-reduction re-
action. It may also be mentioned as exhaust gas
purification catalyst or part of the name of related
devices.

SI

Le Systeme Internation-
al d' Unites (Internation-
al unit system)

Unit

Abbreviation for "International System of Units" It
is the universal unit system and "a single unit for
a single quantity" is the basic principle applied.

SOL

Solenoid

Electrical system

This is an actuator that consists of a solenoid and
an iron core that is operated by the magnetic
force when the solenoid is energized.

ABBREVIATION LIST

20 STANDARD VALUE TABLE

20-6

PC500LC-10R

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов