manualshive.com logo in svg

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 435 / 758

Поделиться
Скачать
Komatsu PC500LC-10R Скачать руководство пользователя страница 435

4.

Remove the plate (5) of the engine flywheel housing, and
insert the gear A.

5.

Rotate the crankshaft in the normal direction with gear A,
align the stamped mark (11) on the crank pulley (10) to the
fan  shaft  center  from  the  undercover  (2)  side  in  order  to
set No. 1 cylinder to the compression top dead center.

REMARK

• Check  that  both  of  the  intake  rocker  arm  and  exhaust

rocker  arm  at  the  compression  top  dead  center  are
movable the same amount of valve clearance by hand.

• If  the  rocker  arm  cannot  be  moved,  No.  1  cylinder  is

not at its compression top dead center. In that case, ro-
tate the crankshaft one more turn.

• Only 1 stamped line is made on the circumference.

6.

While No. 1 cylinder is at the compression top dead center,
check the valve clearance marked with ● in the figure.

7.

Rotate  the  crankshaft  clockwise  by  1  turn  and  check  the
valve clearance of the remaining valves marked with ○.

REMARK

You may check the valve clearance of No. 1 cylinder while
No. 1 cylinder is at the compression top dead center. You
may check the valve clearance of each cylinder in the fir-
ing order by turning the crankshaft in the normal direction
by 120 ° at a time.
Firing order: 1-5-3-6-2-4

30 TESTING AND ADJUSTING

TEST AND ADJUST VALVE CLEARANCE

PC500LC-10R

30-29

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов