Komatsu D155AX-8E0 Скачать руководство пользователя страница 218 | Manualshive

Страница: 218 / 420

background image

MECHANICAL SUSPENSION SEAT
METHOD FOR ADJUSTING SEAT IN FORE-AND-AFT DIRECTION

1.

Pull up the fore-aft adjustment lever, set the seat to the de-
sired position.
Fore-and-aft adjustment: 160 mm (16 stages)

2.

After adjusting, release the lever.

METHOD FOR RECLINING SEAT

The reclining of the seat becomes large when the seat is moved forward, and it becomes smaller as the seat is
moved backward. When moving the seat backward, return the reclined seat back to the original position.
1.

Pull up the reclining adjustment lever and set the seat
back to a position which is comfortable for operation.
Foremost reclining: Approx. 66 ° (Approx. 1.9 ° x 35 steps)
Rearmost reclining: Approx. 72 ° (Approx. 1.9 ° x 38 steps)
Sit with your back against the backrest when adjusting. If
your back is not touching the backrest, it may suddenly
move forward.

2.

After adjusting, release the lever.

METHOD FOR TILTING SEAT

Pull up the tilt adjustment lever and adjust the front angle of the seat.

• To raise the front of the seat, apply your weight to the rear

of the seat, while pulling up lever.

• To lower the front of the seat, apply your weight to the front

of the seat, while pulling up lever.

Tilt adjustment: Up 5 °, down 5 ° (3 levels)

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-156

«
...
216
217
218
219
220
...
»

Содержание D155AX-8E0





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D155AX-8E0

Бренд: Douglas Dynamics Страницы: 10

Бренд: Winton Страницы: 20

AutoBoom Rogator 54 Series 1997+

Бренд: Raven Страницы: 40

MEGA MEZZO HI-TEC

Бренд: Valtra Страницы: 11

Бренд: Valtra Страницы: 22

TRASH GUARD PLUS

Бренд: ACF Страницы: 2

Бренд: FENDT Страницы: 51

M26-2 3-E2 Series

Бренд: Manitou Страницы: 175

Бренд: Curtis Страницы: 28

Бренд: LS Страницы: 158

Бренд: Walker Страницы: 32

Бренд: Whirlpool Страницы: 16

Бренд: Toro Страницы: 2

Бренд: Toro Страницы: 64

Бренд: KUHN Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды