manualshive.com logo in svg

Komatsu D155AX-8E0, Руководство по эксплуатации и техническому обслуживанию, Страница: 240 / 420

Поделиться
Скачать
Komatsu D155AX-8E0 Скачать руководство пользователя страница 240

METHOD FOR STARTING MACHINE (TRAVEL FORWARD AND REVERSE)
AND STOPPING MACHINE

METHOD FOR MOVING MACHINE

k

k

 WARNING

• Check  that  the  area  around  the  machine  is  safe,  and

sound the horn before starting the machine.

• Keep people away from the machine.
• There is a blind spot at the rear of the machine, so be

extremely careful when driving the machine in reverse.

• When starting on a slope, be sure to keep depressing

brake pedal (8), even after you set parking brake lever
(1) free.

• When starting on a steep uphill slope, turn fuel control

dial (5) to High idle (MAX) position and run the engine
at  high  idle,  keep  depressing  brake  pedal  (8)  and  de-
celerator pedal (6), tilt the joystick (steering, direction-
al  and  gear  shift  lever)  from  N  (Neutral)  position  to
FORWARD position, and release brake pedal (8) slow-
ly. When increasing the travel speed, release decelera-
tor pedal (6) slowly.

 

1.

Set parking brake lever (1) to FREE position (F).

2.

Set work equipment lock lever (2) to FREE position (F).

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-178

Содержание D155AX-8E0





































































































































































































































































































































































































































Отзывы:

Нет отзывов