Kohler Mira Sport Multi-fit 1.1746.009 страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 32

background image

12

1493953-W2-A

Replacing an existing shower

.

The Mira Sport Multi-fit is designed to replace showers of approximately the same

size or smaller. Adjustments to existing pipe work and electrical connections may

be necessary to enable the Mira Sport Multi-fit to completely cover the footprint and

screw holes of the previous shower.

Note!

Make sure you allow sufficient clearance

between the ceiling and walls to allow any future maintenance (cleaning the filter

etc.) to be performed.

Supply Entry Points

Plumbing - The inlet water supply can enter from the directions shown.

Note!

By default the water supply position is set for left hand entry, if the installation

favours right hand entry the LH inlet filter (coloured black) and RH inlet connector

plug (coloured red) must be exchanged. Go to "

Adjustment for right hand entry

water supplies"

Rising

Rear fed water supplying

left hand Inlet Connector

Rear fed water supplying

right hand Inlet Connector

Falling

Rotate

inlet to

suit

Rotate

inlet to

suit

Electrical - Terminal Block locations are provided on both the left and right for

convenience when replacing a shower.

Note!

By default the electrical supply position

is set for left hand entry, if the installation favours right hand entry some adjustment

of the terminal block in the case will be required. Go to "

Adjustment for right hand

electrical supplies"

Right Side

Left Side

(Default)

Installation

«
...
10
11
12
13
14
...
»

Содержание Mira Sport Multi-fit 1.1746.009

































Отзывы:

Нет отзывов

Похожие инструкции для Mira Sport Multi-fit 1.1746.009

Бренд: baliv Страницы: 32

Бренд: RAVAK Страницы: 12

Бренд: baliv Страницы: 32

103534-000-270-001

Бренд: MAAX Страницы: 28

Бренд: Grohe Страницы: 12

Бренд: S&P Страницы: 32

Бренд: Oras Страницы: 32

Бренд: habitat et jardin Страницы: 4

Бренд: Sanela Страницы: 5

Бренд: Nadoli Страницы: 23

Бренд: Graham Field Страницы: 2

Бренд: Hans Grohe Страницы: 20

4-part corner entry with swing doors

Бренд: Concept2 Страницы: 15

Бренд: Zomodo Страницы: 4

Бренд: FORENO Страницы: 2

Бренд: Foremost Страницы: 11

Бренд: ERLIT Страницы: 13

Бренд: Vermeiren Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды