Kohler KCP MPAC 1000 Скачать руководство пользователя страница 12

Страница: 12 / 76

TP-6126 8/02

Section 1 Product Description

1.3 Model Code

Record the transfer switch model designation in the boxes below. The transfer switch model designation defines
characteristics and ratings as explained in the accompanying chart.

Kohler

rrrr

Model Designation Key

This chart explains the Kohler

transfer switch model designation system. The sample

model designation shown is for a Model K automatic transfer switch that uses an
open-transition contactor with MPAC 1000

electrical controls rated at 480 volts/60 Hz,

3 poles, 4 wires, and solid neutral in a NEMA 1 enclosure with a current rating of
225 amperes. Not all possible combinations are available.

Model

K: Model K automatic transfer switch

Electrical Controls

A: MPAC 1000

(Microprocessor ATS Controls)

Number of Poles/Wires

Enclosure

0030
0070
0104
0150

0200
0225
0260
0400

0600
0800
1000

1200
1600
2000

2600
3000
4000

KCT-AMTA-0225S

SAMPLE MODEL DESIGNATION

Mechanism

C: Automatic
B: Bypass Isolation (See G11-81)
N: Non-automatic

Transition

T: Open-Transition
P: Programmed-Transition

Power Connections

S: Standard
F: Front bus (available on 1600 and 2000 A models only)

208 Volts/60 Hz

220 Volts/50 Hz

240 Volts/60 Hz

380 Volts/50 Hz

400 Volts/50 Hz

416 Volts/50 Hz

440 Volts/60 Hz

480 Volts/60 Hz

600 Volts/60 Hz

Voltage/Frequency

N: 2-pole, 3-wire, solid neutral
T: 3-pole, 4-wire, solid neutral
V: 4-pole, 4-wire, switched neutral

W: 4-pole, 4-wire, overlapping neutral
Z: 3-pole, 4-wire, integral solid neutral*

A: NEMA 1

[

B: NEMA 12

]

C: NEMA 3R

]

D: NEMA 4

]

F: NEMA 4X

]

G: Open unit

Model

Controls

Voltage

Poles

Enclosure

Current Rating

Connections

Mechanism Transition

[

Standard on 30--4000 A models

]

Available to order on 30--800 A models. For larger units, consult the factory.

Current Rating:

Numbers indicate the current rating of the switch in amperes:

* Integral solid neutral is a solid neutral mounted on the contactor.

(Not available on all amperages.)

Содержание KCP MPAC 1000













































































Результаты поиска

Содержание KCP MPAC 1000

Отзывы:

Похожие инструкции для KCP MPAC 1000

Бренды по названию

Популярные бренды

Kohler KCP MPAC 1000, Эксплуатация и установка

Результаты поиска

Содержание KCP MPAC 1000

Отзывы:

Похожие инструкции для KCP MPAC 1000

Бренды по названию

Популярные бренды