Kohler KCP MPAC 1000 Скачать руководство пользователя страница 63

Страница: 63 / 76

TP-6126 8/02

Section 6 Accessories

6126

Figure 6-22

12-Volt Battery Charger Connections

6126

Figure 6-23

24-Volt Battery Charger Connections

12. Connect the charger to the battery according to the

generator

set

battery

manufacturer’s

instructions, watching the polarity (+/--) of the
connections.

13. Close the enclosure door and reconnect power to

the transfer switch after the charger connections
are complete.

14. Use a voltmeter to check the voltage at the battery

and compare the readings to Figure 6-25 or
Figure 6-26 to verify charger operation.

Battery Charger Disconnection Procedure

Hazardous voltage.
Will cause severe injury or death.

Disconnect all power sources before
opening the enclosure.

DANGER

1. Before opening the transfer switch enclosure,

disconnect power to the transfer switch by opening
switches or circuit breakers to the transfer switch.

2. Disconnect the AC power cord at the in-line

connector.

3. Remove the black (NEGATIVE) wire from the the

battery terminal first.

4. Remove the red (POSITIVE) wire from the battery

terminal.

Содержание KCP MPAC 1000













































































Результаты поиска

Содержание KCP MPAC 1000

Отзывы:

Похожие инструкции для KCP MPAC 1000

Бренды по названию

Популярные бренды

Kohler KCP MPAC 1000, Эксплуатация и установка

Результаты поиска

Содержание KCP MPAC 1000

Отзывы:

Похожие инструкции для KCP MPAC 1000

Бренды по названию

Популярные бренды