background image

4.1

4

Section 4

Air Cleaner and Air Intake System

Air Cleaners

General

Most engines are equipped with a replaceable, high-
density paper air cleaner element, surrounded by an
oiled foam precleaner, and housed under a flat outer
cover. This is typically referred to as the standard air
cleaner assembly. See Figures 4-1 and 4-4. Some
engines utilize a heavy-duty style air cleaner as shown
in Figure 4-12.

Figure 4-2. Removing Latch Style Cover.

Figure 4-1. Standard Air Cleaner.

Standard Air Cleaner

Service

Check the air cleaner 

daily or before starting the

engine

. Check for and correct any buildup of dirt and

debris, along with loose or damaged components.

NOTE: Operating the engine with loose or damaged

air cleaner components could allow
unfiltered air into the engine, causing
premature wear and failure.

Figure 4-3. Removing Knob Style Cover.

Precleaner Service

If so equipped, wash and reoil the precleaner every 

25

hours

 of operation (more often under extremely dusty

or dirty conditions).

To service the precleaner, perform the following steps:

1. Unhook the latches or loosen the retaining knob,

and remove the cover.

2. Remove the foam precleaner from the paper air

cleaner element.

Cover

Precleaner

Air Cleaner Element

Содержание COMMAND CH18









































































































































































































































Отзывы: