background image

10.12

Section 10
Inspection and Reconditioning

Figure 10-13. Removing Governor Gear.

2. Remove the locking tab thrust washer located

under the governor gear assembly.

3. Carefully inspect the governor gear shaft and

replace it only if it is damaged. After removing
the damaged shaft, press or lightly tap the
replacement shaft into the closure plate to the
depth shown in Figure 10-14.

Reassembly

1. Install the locking tab thrust washer on the

governor gear shaft with the tab down.

2. Position the regulating pin within the governor

gear/flyweight assembly and slide both onto the
governor shaft.

Oil Pump Assembly

Disassembly

1. Remove the two hex flange screws.

2. Remove the oil pump assembly from the closure

plate.

3. Remove the oil pump rotor.

4. Remove the oil pickup by unhooking the locking

clip, and pulling it free from the oil pump body.

5. If the relief valve is like that shown in Figure

10-15, drive out the pin to remove the oil pressure
relief valve piston and spring. Refer to the
following inspection and reassembly procedures.

If the relief valve is a one-piece style, staked to the
oil pump housing (See Figure 10-16) removal
should not be attempted, nor is internal servicing
possible. If a problem with the relief valve is
encountered, the oil pump should be replaced.

Disassembly

The governor gear 

must

 be replaced once it is

removed from the closure plate.

NOTE: The governor gear is held onto the shaft by

small molded tabs in the gear. When the gear
is removed from the shaft, these tabs are
destroyed and the gear must be replaced.
Therefore, remove the gear 

only

 if absolutely

necessary.

1. Remove the regulating pin and governor gear

assembly. See Figure 10-13.

Figure 10-14. Governor Shaft Press Depth.

Gear Shaft

34.0 mm (1.3386 in.)
33.5 mm (1.3189 in.)

19.40 mm (0.7638 in.)

Figure 10-15. Oil Pump, Oil Pickup, and Relief Valve
(Original Style).

Pickup

Relief Valve

Содержание COMMAND CH18









































































































































































































































Отзывы: