manualshive.com logo in svg

Knick SensoGate WA 131 H, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA 131 H Скачать руководство пользователя страница 5

5

Intended Use

SensoGate® WA 131 H

Intended Use

The SensoGate® WA 131 H hygienic sensor lock-gate is used for installing a sensor for measure-

ments in liquids. The sensor can be cleaned, calibrated or replaced under process conditions 

 (pressure and temperature).

The operator can exchange process adaptations (Ingold socket, dairy pipe, Varivent, BioControl, 

Clamp) or convert the fitting for the use with gel sensors or liquid-electrolyte sensors.

The sensor lock-gate is suitable for sensors with an outer diameter of 12 mm:

• with gel electrolyte, length 225 mm, sensor head with PG 13.5

• with liquid electrolyte, length 250 mm

The SensoGate® WA 131 H sensor lock-gate allows:

• calibrating or adjusting the measuring system and cleaning the sensor in the running process

• replacing the sensor in the running process

• variable process adaptation by the operator at any time

Take account of the influences of humidity, ambient temperature, chemicals and corrosion.

   Safe use

 If you are not sure whether the sensor lock-gate can be safely used for your intended 

application, please contact the manufacturer.

To ensure safe use of the equipment, you must follow the instructions given in this manual and 

observe the specified temperature and pressure ranges.

The SensoGate® WA 131 H sensor lock-gate has been developed and manufactured in compli-

ance with the applicable European guidelines and standards. Compliance with the European 

Harmonized Standards for use in hazardous locations is confirmed by the EC-Type-Examination 

Certificate. Compliance with the European guidelines and standards is confirmed by the EC 

Declaration of Conformity.

For hazardous-area applications, the sensors used must ensure proper separation of the ATEX 

zones.

There is no particular direct hazard caused by the operation of the device in the specified 

 environment.

Hygienic Design

With regard to hygienic design and sterilizability, the retractable fitting complies with the 

recommendations of EHEDG. This was established and verified in the TNO report V7942 dated 

February 25, 2008. If required, the TNO report can be viewed or obtained from the manufacturer.

Содержание SensoGate WA 131 H

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды