Knick SensoGate WA 131 H Скачать руководство пользователя страница 23

Страница: 23 / 48

Replacing the Immersion Tube

The immersion tube must be removed or replaced:

• for general maintenance

• for cleaning the immersion tube, e.g. after the sensor is broken

• for replacing the sensor gasket (O-ring)

• when an immersion tube made of another material is required

• in the event of a technical fault of the drive unit

WARNING!

To separate the sensor lock-gate safely from the process, make sure

that it is disconnected from all process media and process pressure.

CAUTION!

Before working on the drive unit, make sure that the sensor lock-gate is in

SERVICE position (see “Function Description” on page 10).

First, separate the drive unit from the process unit. (See “Removing the Drive Unit” on page 21.)

1) After having separated the drive unit from

the process unit, move the drive unit into

PROCESS position.

2) In PROCESS position two screws

(Z)

are

accessible.

3) Loosen the two screws

(Z)

by approx. 4 turns

using a screwdriver (TX25) (do not remove

them).

4) Turn the immersion tube

(T)

counter clockwise

by approx. 60°.

5) The bayonet coupling opens and the immer-

sion tube

(T)

can be pulled out in direction of

the arrow.

6) Now, O-ring

(D)

(sensor gasket) is visible.

Check and replace if required. (For O-ring

dimensions, see page 43 “Sealing Kits for

Maintenance and Servicing”.)

Note:

Contrary to the figure, the O-ring may still be

in the immersion tube. From there, you can

easily remove it.

Removing the Immersion Tube

Screwdriver no. 6

included in accessory:

ZU 0680, ZU 0740, ZU 0754

Approx. 60°

Содержание SensoGate WA 131 H

















































Результаты поиска

Содержание SensoGate WA 131 H

Отзывы:

Бренды по названию

Популярные бренды

Knick SensoGate WA 131 H, Руководство пользователя

Результаты поиска

Содержание SensoGate WA 131 H

Отзывы:

Бренды по названию

Популярные бренды