manualshive.com logo in svg

Knick SensoGate WA 131 H, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA 131 H Скачать руководство пользователя страница 42

42

Sealing Kits for Maintenance and Servicing

SensoGate® WA 131 H

The sealing kits are available in different materials. The smaller sealing kits (“Set X/1”) only contain 

gaskets for direct contact with the process. 

The extended sealing kits (“Set X/2”) also include gaskets for contact with the rinse medium.

NOTICE! 

Take account of the process adaptations.

Special sealing kits are available for Ingold sockets.

The sealing kits come with detailed illustrations for installation. 

The new gaskets must be lubricated with the included lubricant.

The following sealing kits are available:

Gaskets

Order No.

Process 

 connection

dairy pipe,

Tri-Clamp,

Varivent,

BioControl

Set E/1

Process-wetted sealing material: EPDM FDA

ZU 0700/1

Set E/2

Process-wetted sealing material: EPDM FDA,  

wetted by rinse medium: EPDM FDA

ZU 0841

Set F/1

Process-wetted sealing material: FKM FDA

ZU 0697/1

Set F/2

Process-wetted sealing material: FKM FDA,  

wetted by rinse medium: FKM FDA

ZU 0842

Set G/1

Process-wetted sealing material: FFKM FDA

ZU 0766/1

Set G/2

Process-wetted sealing material: FFKM FDA,  

wetted by rinse medium: EPDM FDA

ZU 0843

Set H/1

Process-wetted sealing material: FFKM FDA,

ZU 0766/1

Set H/2

Process-wetted sealing material: FFKM FDA,  

wetted by rinse medium: FFKM FDA

ZU 0844

Process 

 connection

Ingold socket H0

Set E/1

Process-wetted sealing material: EPDM FDA

ZU 0704/1

Set E/2

Process-wetted sealing material: EPDM FDA,  

wetted by rinse medium: EPDM FDA

ZU 0845

Set F/1

Process-wetted sealing material: FKM FDA

ZU 0703/1

Set F/2

Process-wetted sealing material: FKM FDA,  

wetted by rinse medium: FKM FDA

ZU 0846

Set G/1

Process-wetted sealing material: FFKM FDA

ZU 0768/1

Set G/2

Process-wetted sealing material: FFKM FDA,  

wetted by rinse medium: EPDM FDA

ZU 0847

Set H/1

Process-wetted sealing material: FFKM FDA

ZU 0768/1

Set H/2

Process-wetted sealing material: FFKM FDA,  

wetted by rinse medium: FFKM FDA

ZU 0848

Process 

 connection

Ingold socket H1

Set E/1

Process-wetted sealing material: EPDM FDA

ZU 0704/1

Set E/2

Process-wetted sealing material: EPDM FDA,  

wetted by rinse medium: EPDM FDA

ZU 0849

Set F/1

Process-wetted sealing material: FKM FDA

ZU 0703/1

Set F/2

Process-wetted sealing material: FKM FDA,  

wetted by rinse medium: FKM FDA

ZU 0850

Set G/1

Process-wetted sealing material: FFKM FDA

ZU 0768/1

Set G/2

Process-wetted sealing material: FFKM FDA,  

wetted by rinse medium: EPDM FDA

ZU 0851

Set H/1

Process-wetted sealing material: FFKM FDA

ZU 0768/1

Set H/2

Process-wetted sealing material: FFKM FDA,  

wetted by rinse medium: FFKM FDA

ZU 0852

Содержание SensoGate WA 131 H

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды