manualshive.com logo in svg

Knick SensoGate WA 131 H, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA 131 H Скачать руководство пользователя страница 16

16

Installing and Removing a Sensor

SensoGate® WA 131 H

 

Sensors must only be installed or removed by trained personnel authorized by the 

operating company. 

Make sure that the sensor lock-gate is in SERVICE position

 

(see “Function Description” on page 10)

. 

WARNING!

Process fluids leaking from the outlet or at the leakage holes (see “Build-Up of the 

Sensor Lock-Gate” on page 13) show that the calibration chamber is not tight.

Be sure to follow the assembly instructions step by step.

Preparations:

•  Check whether the sensor is damaged (glass broken?).  

Never install a damaged sensor.

•  Check whether slide washer or O-ring on the sensor are damaged and replace if required.

•  Remove watering cap from the sensor tip and rinse sensor with water.

•  Internally pressurized sensors might have a silicone seal on the diaphragm (as transport 

 protection). Remove this seal using the knife shipped with the sensor.

Содержание SensoGate WA 131 H

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды