KNEGT 404G2 Series Скачать руководство пользователя

Страница: 43 / 105

404G2

SERIES TRACTOR OPERATION MANUAL

4.2.4

Start

the

Tractor

1. Loose the park brake system and press the horn then check the surroundings.

2. Depress the clutch pedal to the end, shift to a proper

gear. If it fails, then loose the clutch pedal, and do

these procedures again.

Step up the tractor, and loose the clutch pedal slowly

at the same time.

4.2.5

Driving

the

Tractor

1.The tractor’s driving

(1) The choice of gear. This series of tractors has eight

forward gears and eight backward gears. The selection of

the tractor

’

s gear should based on regional geology

、

climate and work

type. The proper

selection of gear,

can achieve

maximum

productivity and

economical

efficiency, and can

prolong the service

life of the tractor.

The tractor should

not be often overload, The tractor work at 80% of the maximum power, let the tractor

engine has a certain power reserves.

a) The basic gears of work are :Plough often use low

Ⅲ

gear, low

Ⅵ

gear, high

Ⅰ

gear; rotary tillage often use low

Ⅰ

gear, low

Ⅱ

gear, traction operations often use low

Ⅲ

gear, low

Ⅵ

gear, high

Ⅰ

gear, high

Ⅱ

gear; transport operations often use high

Ⅱ

gear, high

Ⅲ

gear, high

Ⅵ

gear. Spindle gear , the main gear, high and low gear

as shown in fig 4-12.

Range Shift Lever

See.fig.4-1No.3

Shuttle Shift Lever

See.fig.4-1No.8

Gear shift lever

See.fig.4-1No.15

Fig.4-12

Fig.4-11

A. Park brake control lever

B. Brake pedals

Содержание 404G2 Series










































































































Результаты поиска

Содержание 404G2 Series

Отзывы:

Похожие инструкции для 404G2 Series

Бренды по названию

Популярные бренды

KNEGT 404G2 Series, Руководство по эксплуатации

Результаты поиска

Содержание 404G2 Series

Отзывы:

Похожие инструкции для 404G2 Series

Бренды по названию

Популярные бренды