KNEGT 404G2 Series Скачать руководство пользователя

Страница: 61 / 105

404G2

SERIES TRACTOR OPERATION MANUAL

⑥

front axle arms

⑦

left and right front wheel housings

Checking point

①

Engine dipstick

②

Rear axle housing dipstick,

Dipstick on left half shaft housing of front wheel drive axle

③

④

Checking plug on the cover of air pump

Oil outlet,

①

Bottom of engine sump,

②

bottom of rear axle,

④

bottom of air pump

；

⑤

bottom of front drive center housing, and

bootom of left and right retarder housing.

5.2 Periodic Service

According to accumulated working hours, technical maintenance of

KNEGT

series

tractor should be operated every 10h, 50h, 200h, 400h, 800h or 1600h.

Details of the engine’s maintenance can be refered in the manual of engine.

5.2.1

10h

maintenance

、

Engine

①

Check the liquid level of engine sump

，

refill them if they are insufficient

，

and

make sure the level will be between the middle notch and the topper notch on

the dipstick. Never exceed the topper notch. A new tractor or one haven’t used

for a long time, the level must be checked again after filling and operating for

5 to 10 minutes.

②

Fill in enough diesel oil and cooling water.

、

Chassis

①

Check and fasten every external linkage bolts and nuts.

②

Use a press rod oil gun at these places: left and right retarder housing.

③

Check and eleminate if there is a leakage of oil, water or air. Clean off the dirt

and mud on the tractor.

④

Check the air pressure of front and rear tires, and inflate if they are insufficient.

、

Air Conditioning Systems

①

Check cleaning condenser, and insure the radiating fins clean and expedite.

②

Check the drive belt of compressor and engine, and insure it’s not loose.

Содержание 404G2 Series










































































































Результаты поиска

Содержание 404G2 Series

Отзывы:

Похожие инструкции для 404G2 Series

Бренды по названию

Популярные бренды

KNEGT 404G2 Series, Руководство по эксплуатации

Результаты поиска

Содержание 404G2 Series

Отзывы:

Похожие инструкции для 404G2 Series

Бренды по названию

Популярные бренды