KNEGT 404G2 Series Скачать руководство пользователя

Страница: 28 / 105

404G2

SERIES TRACTOR OPERATION MANUAL

Chapter

Running

the

tractor

In order to prolong the service life of tractors, it is essential to break-in a new tractor or

the engine after a major overhaul, before putting it into service. Breaking-in improves

all of the fittings and contact surfaces in order to avoid premature failures.

3.1 Preparation before Running-in of the tractor

1. Please check and tighten the outside screws.

2. Add grease into all the grease fittings.

3. Check the oil lever of engine, gearbox and rear axle, final transmissions, front wheel

drive axle, steering oil tank and hydraulic system. If it is not enough, then supply

again.

4. Fill some fuel and cooling water.

5. Check air pressure of the the tires.

6. Check proportion and height of battery electrolyte.

7. Put Shuttle shift lever, PTO shift lever ,range shift lever and gear shift lever on

“netural” position.Disengage the 4WD. Lifting mechanism control at lowered

position.

3.2 Running-in the engine without load

Running-in engine for 15 minutes without load.Start the engine in accordance with the

procedure specified in the Instruction Manual, let the engine running-in 7 minutes in

hight speed, 5minutes in mid speed, 3 minutes in high speed.

During the running-in of engine without load, should carefully check the work condition

of engine, air compressor and hydraulic pump.Observe if have abnormality, noise and

check leakages of water, oil and air. If the meters work abnormally, should stop and

remedy the trouble to restart running-in when find abnormality.

Running-in as below when you confirm the engine working is abnormal.

Содержание 404G2 Series










































































































Результаты поиска

Содержание 404G2 Series

Отзывы:

Похожие инструкции для 404G2 Series

Бренды по названию

Популярные бренды

KNEGT 404G2 Series, Руководство по эксплуатации

Результаты поиска

Содержание 404G2 Series

Отзывы:

Похожие инструкции для 404G2 Series

Бренды по названию

Популярные бренды