KMB NOVAR 2100 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 77

background image

NOVAR 2100/2200 Operating Manual

4.6.3 Embedded Electricity Meter............................................................................................................... 60

4.6.3.1 Electric Energy Processing......................................................................................................... 60
4.6.3.2 Maximum Demand Registration.................................................................................................60

4.7 Special PFC-Block Related Quantities' Meaning & Method of Evaluation.........................................60

4.7.1    ΣΔQfh – PF Control Deviation........................................................................................................... 60
4.7.2    CHL – Capacitor Harmonic Load Factor...........................................................................................61
4.7.3    RC, RL – Compensation Reserve Powers........................................................................................63

5. COMPUTER CONTROLLED OPERATION.....................65

5.1 Communication Interface...................................................................................................................... 65

5.1.1 Service USB Interface........................................................................................................................ 65
5.1.2 RS-485 Interface (COM)................................................................................................................... 65

5.1.2.1 Communication Cable................................................................................................................ 65
5.1.2.2 Terminating Resistors................................................................................................................ 65

5.1.3 Ethernet Interface (ETH)................................................................................................................... 65

5.2 Communication Protocols..................................................................................................................... 66

5.2.1 KMB Communications Protocol........................................................................................................ 66
5.2.2 Modbus Communications Protocol...................................................................................................66

5.3 Embedded Webserver............................................................................................................................. 66

6. EXAMPLES OF CONNECTIONS....................................67

7. MANUFACTURED MODELS AND MARKING................73

8. TECHNICAL SPECIFICATIONS......................................74

9. MAINTENANCE, SERVICE.............................................77

4

«
...
2
3
4
5
6
...
»

Содержание NOVAR 2100














































































Отзывы:

Нет отзывов

Похожие инструкции для NOVAR 2100

Бренд: Samson Страницы: 20

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Idesco Страницы: 11

Бренд: B meters Страницы: 2

Бренд: Zeagle Страницы: 37

Бренд: Magnescale Страницы: 3

Бренд: Yngri Страницы: 20

Бренд: CAME Страницы: 2

Бренд: Westfalia Страницы: 18

Бренд: Samcen Страницы: 65

Бренд: Hard Head Страницы: 10

VENMAR ADVANCED TOUCHSCREEN CONTROL

Бренд: vanEE Страницы: 4

Бренд: GOAL ZERO Страницы: 52

Бренд: U-Tron Страницы: 8

Бренд: Agilent Technologies Страницы: 20

Compact Performance Series

Бренд: Festo Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды