KITO Harrington RY Series Скачать руководство пользователя страница 93

Страница: 93 / 120

Table 7-7 "Minor Failure/ Warning Error" Display Details and Remedies (Continued)

LED Display

Error name

Uv3

In-rush prevention circuit error

Failure of the in-rush prevention circuit occurred.

Cause

Measure

Failure of the contactor of the in-rush

prevention circuit inside the VFD

Turn on/off the power supply to check if an error occurs.

⇒

If the error

occurs in succession, replace the VFD.

VFD internal atmosphere error

Check the ambient temperature of the VFD.

Table 7-8 "Minor Failure/ Warning" Display Details and Remedies

LED display

Minor failure name

Forward/reverse command simultaneous input

The forward rotation command and reverse rotation command were
inputted simultaneously for 0.5 seconds or more.

Cause

Measure

Sequence error

Review and modify the wiring of the forward/reverse command.

LED display

Minor failure name

EF1 to EF7

External error (Input terminal S1 to S7)

An external error was inputted from the multifunction contact input
terminal (S1 to S7)

Cause

Measure

The alarm function of the external
equipment is operating.

-Remove the cause of the external error input of the multifunction input.

The wiring is not correct.

Check that the signal line is correctly connected to the external input
terminal.

-Connect the signal line correctly.

LED Display

Minor failure name

Hbb

Safety signal is being inputted.

A safety signal was inputted from the input terminal.

Cause

Measure

-If not reset by releasing the emergency stop button, check the wiring
related to the push button switches (signal line).

LED Display

Minor failure name

HCA

Current warning

The VFD output current exceeded the overcurrent warning level (150% of
the rated current).

Cause

Measure

The load is too high.

Measure the current flowing through the motor.

⇒

If overload occurs, reduce the load, or increase the inverter (VFD)

capacity.

Содержание Harrington RY Series

























































































































Результаты поиска

Содержание Harrington RY Series

Отзывы:

Похожие инструкции для Harrington RY Series

Бренды по названию

Популярные бренды

KITO Harrington RY Series, Руководство пользователя

Результаты поиска

Содержание Harrington RY Series

Отзывы:

Похожие инструкции для Harrington RY Series

Бренды по названию

Популярные бренды