Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 21 / 69

5-6. Recommended operation oil

(For air hydro booster at pneumatic/hydraulic spec.)

(Viscosity grade ISO VG32)

Maker

Name

IDEMITSU

Daphne Neo Fluid 32

Daphne Super Hydro 32A

MOBIL

Mobil DTE XL32

JX NIPPON OIL & ENERGY

Super Hyrando SE32

SHELL

Shell Tellus Oil 32

COSMO

Cosmo Super Epoch ES32

5-7. Safety of Oil and Antirust Oil Used for the Unit

5-7-1. Scope of application

・

Specified lubricating oil

・

Specified hydraulic oil

（

，

MRT

，

RK, TM2100

･

3100

，

TH2100

･

3100

，

TT(TW)101

･

120

，

TT140

，

TT150

，

DM do not use

）

・

Antirust oil applied to the unit at delivery (Houghton Japan, Rust Veto 377)

5-7-2. First-aid treatment

Aspiration : In case of much aspiration, go to a place where there is fresh air, and cover your body

with a blanket to keep your body warm. Consult a doctor if necessary.

Sticking to your skin: Wipe off the oil, and wash your skin with water and soap. If you feel itchy or you get

inflamed, consult a doctor immediately.

Entering your eye: Wash your eye with fresh water for at least 15 minutes, and then consult a doctor.

Accidental drinking: Consult a doctor immediately without vomiting forcibly. If you are polluted in your

mouth, wash with water thoroughly.

・

For lubrication oils and hydraulic oils other than specified ones, and antirust oils prepared by the

customer, refer to the safety information prepared for respective oils.

5-7-3. Flammable characteristics

・

Watch out for fire since lubricating oil and hydraulic oil are flammable. Hazardous substances

will be generated if they combusted.

・

The flash point of lubricating oil and hydraulic oil put in the unit at the delivery exceeds 200



C. It

may be different from that of the lubricating oil and hydraulic oil prepared by the customer.

・

Antirust oil is highly volatile and thus likely to catch fire, and also it mixes with air to form

explosive mixture gas.

・

The flash point of antirust oil applied to the unit at the delivery is 38



C. It may be different from

that of the antirust oil prepared by the customer.

5-7-4. Disposal of lubricating oil and hydraulic oil

Dispose of used lubricating oil and hydraulic oil exhausted from this unit in accordance with the laws and

regulations of your country. You may suffer punishment if you disposed of waste oil without following the

laws and regulations.

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды