Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 49 / 69

Symptom

③：

Table does not rotate smoothly but generates a noise

Possible causes

Corrective actions

Noise is generated repeatedly during
rotation

→

Gears are damaged

Stop the use of NC rotary table immediately.

Please contact the sales agent.

→

Faulty rotation of gears because foreign
substances mix in the oil bath

Open the lubricating oil drain port, and
supply lubricating oil until foreign substances
come out of the drain port.

Load due to overloading exceeds motor
output

Compare the specification of NC rotary table
with the work condition to make
improvement

Lack or deterioration of lubricating oil blocks
smooth rotation

Check oil level, viscosity and change interval
of lubricating oil

Faulty clamp device

See

“Symptom

⑤

”

Inappropriate backlash amount

Adjust backlash amount to appropriate value

Symptom

④：

Chattering occurs during cutting

Possible causes

Corrective actions

Inappropriate clamp condition of NC rotary
table or fixture

Check the clamp condition, and correct it

Excess cutting force is applied during cutting

Adjust cutting condition to the specified
condition to change the cutting force to
appropriate value

Faulty clamp device

See

“Symptom

⑤

”

Faulty locking of worm spindle in the
backlash adjustment

Readjust

Fault due to damaged NC rotary table or
expired life of components

Stop the use of NC rotary table immediately.
Please contact the sales agent.

Fault occurs only during continuous cutting

→

Lack or deterioration of lubricating oil
blocks smooth rotation

Check oil level, viscosity and date of last
change of lubricating oil
Adjust backlash amount to appropriate value

→

Inappropriate backlash amount

Chips accumulate in rotary part of NC rotary
table

Remove

accumulated

chips

daily

inspection

Symptom

⑤：

Table is not clamped or unclamped

Possible causes

Corrective actions

Faulty solenoid valve

Replace the solenoid valve

Faulty clamp/unclamp confirming device
(pressure switch)

Check and replace the clamp/unclamp
confirming device (pressure switch)

Damage or connection failure of working
fluid pipe for clamp

Check the piping for connection, and replace

Supply pressure of working fluid for clamp is
lower than specified value

Change to appropriate value according to
the specification

Back pressure acts to the air pressure
exhaust port of solenoid valve, as the air
purge port in the motor case is blocked.

Remove the cause that blocks the air purge
port.

Faulty clamp device

Stop the use of NC rotary table immediately.
Please contact the sales agent.

Fault due to damaged NC rotary table or
expired life of components

Stop the use of NC rotary table immediately.
Please contact the sales agent.

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды