Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 40 / 69

The proximity switch is used as the dog detecting sensor. The gap between the dog and the proximity

switch is set to about 0.75mm. (Thread pitch for mounting the proximity switch is 1mm.) The proximity

switch with a lamp is used. When the dog is detected, since the lamp goes off, use the proximity switch

as a target when the dog position is adjusted.

13-1-2. Tilting axis ZRN device (See Fig.12-2)

1) The ZRN deceleration dog and the proximity switch are contained into the rotating axis motor case.

2) In the standard specification, the horizontal table face position is regarded as an origin. The proximity

switch

②

detects dog

①

Set screw

③

Cover

①

Dog

②

Cover

④

Proximity switch

0.75mm

Fig.12-1

Fig.12-2

Dog A

①

(for zero decel. return)

Proximity SW

②

(for zero decel. return)

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды