Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 46 / 69

16-3. To mount spur gears

The mounting method of spur gears varies by the motor shaft and flange diameter. The following

procedure is recommended to mount the spur gears by three-method mainly used.

○

Taper shaft

1) Wipe up dust adhered on the taper shaft surface and inside of spur gears.

2) Attach the key to the shaft before mounting the spur gear.

3) Attach the washer and tighten the nut securely.

○

Straight shaft (with key)

1) Wipe up dust adhered on the straight shaft surface and inside of spur gears.

2) Attach the key to the shaft.

3) Fix the spur gear and waster securely.

4) Mount the spur gear with the washer to the shaft securely by using the bolt.

○

Straight shaft (locking element spec.)

1) Wipe up dust adhered on the straight shaft surface and inside of super gears and coat them with oil

or grease. However, do not use lubricate of silicon system or molybdenum system, or oil and grease

including an extreme-pressure additive agent.

2) Insert the washer, locking element, spacer and spur gear in order.

3) At this time, attach the locking element (Generic name for inner ring and outer ring) so as to

pressurize the inner ring.

4) Tighten bolts on each diagonal line equally in order so that the end face of spur gear and the flange

end face of motor become parallel.

5) Tighten the bolts until washers do not move in an axial direction. After that, adjust the mounting

position of spur gear.

6) Attach the dial gauge to the end face of spur gear and tighten bolts equally. Rotate the spur gears

and also, tighten each bolt until the run out of dial gauge becomes 0.01mm or less.

7) Check that the spur gears are fixed to the shaft securely.

Fig.17

Washer

Spur gear

Bolt

Detail part A

Spacer

Inner ring

Motor

Spur gear

Key

Nut

Motor

Key

Washer

Spur gear

Bolt

Taper shaft

Straight shaft (with key)

Locking element

Straight shaft (locking element spec.)

Outer ring

Dial gauge

Spur gear

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды