Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 18 / 69

5. Operation Ready

After unpacking, the tilting rotary table is mounted to the machine tool. Observe the following procedure

before performing the operation (trial run).

5-1. Table transfer and mounting to machine tool

1) When transporting the unit, hook ropes to the eyebolts attached and transport the unit carefully, not

giving a shock. The ropes used should be wire ropes having enough strength to lift up the unit.

2) Clean the table face on the machine tool and the mounting base surface of NC table after checking

that burr or flaw is not found. If the burr or flaw is found, repair them with the oil grinding stone.

3) The motor case may be removed depending on the maintenance work. Accordingly, whenever possible,

install the NC rotary table in a position where the motor case can be removed. In case of vertical

installation, the guide blocks will fit into the slotted groove on the machine. If there is any play between

the guide

block and the T-slot, place the unit against one side of the T-slot to eliminate the gap.

4) Securely fix the NC rotary table to the machine tool with the attached clamper.

Do not enter a part of your body under the NC rotary table during

transportation.

Unexpected accidents such as a disengagement of lifting devices may

cause the NC rotary table to drop on your body.

When mounting the NC rotary table to the machine tool, check the

mounting space carefully. Especially, take care so that the NC rotary

table, cables and air/hydraulic hoses will not interfere with the splash

guard or ATC device and spindle head of machine tool because the table

or spindle head moves.

Do not damage the cables by placing a heavy thing or pinching them. If

the cables are damaged, there is a danger of electric shock.

Tighten the bolts of clamper at the specified torque by using the

mounting seat effectively.

The transport and lifting devices must be operated only by the qualified

persons for respective devices.

Operating the transport devices by an unqualified person causes the NC

rotary table or machine to be damaged due to an operation error,

resulting in accidents.

DANGER

WARNING

CAUTION

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды