manualshive.com logo in svg

KIRLOSKAR GK 10, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
KIRLOSKAR GK 10 Скачать руководство пользователя страница 63

 

IOM/GK(P)/CONICAL                                                                                  ISSUE DATE: 10.11.2015  
Page 63                                                                                               LAST REV. DATE: 01.08.2019

 

 

 

 

 

CORRECT

STEEL STRAIGHT EDGE

 

INCORRECT PARALLEL        

      MISALIGNMENT

STEEL STRAIGHT EDGE

STEEL STRAIGHT EDGE

 

INCORRECT ANGULAR    

  

      MISALIGNMENT

            2) Parallel misalignment – Shaft with axis parallel, but not concentric. 
                Maximum allowable misalignment is 0.1 mm. 

 

LEVELING THE UNIT 

When  the  unit  is  received  with  the pump  and driver  mounted  on  the base  plate,  it 
should  be  placed  on  the  foundation  and  the  coupling  halves  disconnected.  The 
coupling  should  not  be  reconnected  until  all  misalignment  operations  have  been 
completed. The base plate must be supported evenly on wedges inserted under the 
four corners so that it will not be distorted or sprung by the uneven distribution of 
the  weight.  Adjust  the  wedges  until  the  shafts  of  the  pump  and  the  driver  are  in 
level.  Check  the  coupling  faces,  suction  and  discharge  flanges  for  the  horizontal 
and vertical position by means of spirit level. 
 

FLEXIBLE COUPLING ALIGNMENT 

The two halves of the coupling should be at least 3 mm apart so that they cannot 
touch  each  other  when  the  driver  shaft  is  rotated.  Necessary  tools  for 
approximately checking are straight edge or an outside caliper. A check for parallel 
misalignment  is  made by placing  a  straight  edge  across  both  coupling periphery  at 
the top, bottom and both the sides. The unit will be in parallel alignment when the 
straight edge rests evenly on the coupling periphery at all the positions. Care must 
be taken that the straight edge must be parallel to the axis of the shaft. 
 

GROUTING 

When the alignment is correct, the foundation bolts should be tightened evenly but 
not  too  firmly.  The  unit  can  then  be  grouted  by  working  soft  concrete  under  the 
edges.  Foundation  bolts  should  not  be  fully  tightened  until  the  grout  is  hardened, 
usually 48 hours after pouring. 
 

FACTORS THAT MAY DISTURB ALIGNMENT 

The  unit  should  be  periodically  checked  for  alignment.  If  the  unit  does  not  stay  in 
line after being properly installed, the following are possible causes: 

1.

 

Setting, seasoning of the foundation. 

2.

 

Pipe strains distorting or shifting the machines. 

3.

 

Wear of the bearing. 

 

 
 
 

Содержание GK 10






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды