Kimberley KARAVAN 2021 Скачать руководство пользователя страница 7

Страница: 7 / 120

Warranty

the maintenance of lubricants, sealants, and seals;

Condensation and the results of condensation

including water damage and the growth of mold

or mildew. Mold and mildew are natural growths

given certain environmental conditions and are

not covered by the terms of this Limited Warranty;

The addition of weight to the camper-trailer/

caravan that causes the total weight to exceed

applicable weight ratings, or addition of weight

causing improper distribution of the weight of

the camper-trailer/caravan; Failure to seek and

obtain repairs in a timely manner; Failure to use

reasonable efforts to mitigate damage caused by

defects; Failure to properly ventilate the camper-

trailer/caravan; Improper electric power supply or

improper camper-trailer/caravan hookup to other

facilities; the camper-trailer/caravan being subject

to abnormal conditions, including environment,

temperature, water, fi re, humidity, pressure, stress

or similar; the camper-trailer/caravan having

been used after a defect became apparent or

should have become apparent; excessive speed,

failure to lower tyre pressure or hard impact; the

repair, maintenance or service by a person not

authorised by KK; water damage caused by creek

crossings, fl ooding and other similar conditions;

or Acts or omissions of any person or entity

other than KK. (Note: An irrefutable presumption

arises that the camper-trailer/caravan has been

used for commercial and/or business purposes

if the camper-trailer/caravan owner or user fi les

a tax form claiming any business or commercial

tax benefi t related to the camper-trailer/caravan,

or if the camper-trailer/caravan is purchased,

registered or titled in a business name.)

Warranty Transfer Conditions

This warranty is only transferrable to a subsequent

owner if the camper-trailer/caravan is sold by the

original owner during the Warranty Period unless

otherwise agreed to by KK in writing. The subsequent

owner must contact KK to register for the remainder

of the Warranty Coverage Period.

How will a valid Warranty claim be honoured?

If a defect appears in KK’ manufacture or assembly

fo the camper-trailer/caravan before the end of

the Warranty Coverage Period and KK fi nds the

camper-trailer/caravan to be defective in materials or

workmanship, KK will, in it’s sole discretion, either;
• replace or repair the camper-trailer/caravan or the

defective part of the camper-trailer/caravan; or

• cause the camper-trailer/caravan or defective

part of the camper-trailer/caravan to be replace or

repaired by a qualifi ed repairer.

Warranty repairs shall only be carried out by KK’s

service department or, when directed by KK’s Service

Manager, by an authorised KK repair and service

agent within a reasonable time from the camper-

trailer/caravan being delivered to KK.
KK reserves the right to take ownership of all

replaced parts. KK will not reimburse any payments

made for work done or replaced parts done through

unauthorised repairers without prior written consent

from KK.
KK reserves the right to replace defective parts of the

camper-trailer/caravan with parts and components of

similar quality, grade, function and composition where

an identical part or component is not available.
Goods presented for repair may be replaced by

refurbished goods of the same type rather than being

repaired. Refurbished parts may be used to repair the

goods.

Obtaining Warranty Service

To obtain warranty service under this Limited

Warranty, the owner must do all of the following:
1. Owner and dealer representative must complete

the ‘Record of Handover’ in Owner’s Manual

within 10 days from delivery of the camper-trailer/

caravan,

2. Complete and submit the Warranty Registration

Form (link in Operating Manual),

3. Notify KK or one of its authorised, independent

dealers of any claimed defect within the warranty

period or 10 days thereafter,

Provide notifi cation of a defect within 10 days of

discovery of that defect, and

5. Promptly return the camper-trailer/caravan to an

authorised KK dealer or KK for repairs.

If your camper-trailer/caravan develops a defect or is

in an accident or collision, you must not attempt to

repair it yourself. Doing so may cause damage which

is not covered by this Limited Warranty. Only service

agents authorised by KK should perform service or

repairs on the camper-trailer/caravan. You should

therefore contact the KK Service Department if any of

these events occur.
If you believe a defect covered by this Limited

Warranty still exists after an attempted repair by an

authorised KK dealer, you must contact KK at the

following address, specifying:
1. The last 4 digits of the VIN or complete serial

number of the camper-trailer/caravan,

2. The date of original purchase and the date of

original delivery,

Содержание KARAVAN 2021

























































































































Результаты поиска

Содержание KARAVAN 2021

Отзывы:

Похожие инструкции для KARAVAN 2021

Бренды по названию

Популярные бренды

Kimberley KARAVAN 2021, Инструкция по установке, техническому обслуживанию и эксплуатации

Результаты поиска

Содержание KARAVAN 2021

Отзывы:

Похожие инструкции для KARAVAN 2021

Бренды по названию

Популярные бренды