Kimberley KARAVAN 2021 Скачать руководство пользователя страница 4

Страница: 4 / 120

Warranty

3 Year Manufacturer Warranty Policy & 5 Year

Chassis & Suspension Warranty Policy

(AUS June 21)

Kimberley Kampers (hereafter referred to as ‘KK’)

provides the following warranty in relation to it’s

camper-trailers/caravans.

The benefi ts of this warranty are in addition to any

rights and remedies you may have under any laws in

relation to the supply of a camper-trailer/caravan that

cannot be excluded. Nothing in this warranty is to be

interpreted as excluding, restricting or modifying any

such laws which cannot be excluded, restricted or

modifi ed.

Our camper-trailer/caravan comes with guarantees

that cannot be excluded under the Australian

Consumer Law. You are entitled to a replacement or

refund for a major failure and for compensation for

any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or

replaced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.
Please take the time to read the Owner’s Manual to

ensure that you are familiar with the camper-trailer/

caravan’s operation and service procedures.

This Limited Warranty Covers
(i)The fi rst retail owner and any subsequent owners

(ii) ONLY those portions of a NEW camper-trailer/

caravan not excluded under the section “What is Not

Covered”, when sold by an authorised dealership and

used for its intended purpose of recreational travel

and camping; and, (iii) ONLY defects in workmanship

performed and/or materials used to assemble those

portions of your camper-trailer/caravan not excluded

under the section “What is Not Covered”. “Defect”

means the failure of the workmanship performed

and/or materials used to conform with the design

and manufacturing specifi cation and tolerances of

KK. The Limited Warranty is transferable and the

subsequent owner’s warranty coverage period shall

be the unexpired balance of the original warranty

coverage period.
When you request and accept the performance of

warranty repairs under the terms of this Limited

Warranty, you are accepting all terms of this Limited

Warranty, including by way of example, warranty

limitations and disclaimers, the forum selection

clause and the clause reducing the time period when

suit must be fi led for breach.
Coverage Ends

36 Months (Manufacturer Warranty) and 60 Months

(Chassis & Suspension Warranty) after the fi rst retail

owner fi rst takes delivery of the camper-trailer/

caravan from an authorised dealership. Any action

for breach of this warranty or any implied warranties

must be commenced not more than 37 / 61 months

after breach.

Limitation Of Implied Warranties

Implied warranties arising under applicable law, if

any, including but not limited to implied warranties of

merchantability or fi tness for a particular purpose, are

hereby limited in duration to the term of this limited

warranty and are limited in scope of coverage to those

portions of the camper-trailer/caravan covered by this

limited warranty. There are no express warranties or

any implied warranties of merchantability on those

portions of the camper-trailer/caravan excluded from

coverage. There is no warranty of any nature made by

KK beyond that contained in this limited warranty. No

person has authority to enlarge, amend or modify this

limited warranty. The dealer is not KK’s agent. KK is

not responsible for any undertaking, representation or

warranty made by any dealer or others beyond those

expressly set forth within this limited warranty.

Third Party Warranty Items
Items supplied by a Third Party and fi tted by KK are

warranted by said supplier/manufacture. These

items typically include retractable awnings, electrical

appliances and electronic equipment. KK may help

a customer with a warranty claim but will not be

responsible for fulfi lling the warranty obligations of

Third Party Suppliers. If and when new materials

and production techniques are developed that

can improve the quality of its product, or material

substitutions are necessary due to availability,

KK reserves the right to make such changes. The

warranty periods for some of these components

varies by supplier and can be found below:

Item

Supplier

Warranty Periods

Canvas

Wax Converter

Textiles

Limited Warranty up

to 5 Years

Multimedia

Fusion, Intellisat,

TEAC

Limited Warranty up

to 3 Years

Diesel Hot Water

Units

Diesel Air Heater

Units

Various

2 Years

Diesel Cook Tops

Various

2 Years

Lithium Batteries

Kimberley

Limited Warranty

up to 3,000 Hour

(typically this is 5+

years)

Air conditioner

Dometic

2 Years

Toilet

Dometic

Kimberley Waterless

2 Years

Содержание KARAVAN 2021

























































































































Результаты поиска

Содержание KARAVAN 2021

Отзывы:

Похожие инструкции для KARAVAN 2021

Бренды по названию

Популярные бренды

Kimberley KARAVAN 2021, Инструкция по установке, техническому обслуживанию и эксплуатации

Результаты поиска

Содержание KARAVAN 2021

Отзывы:

Похожие инструкции для KARAVAN 2021

Бренды по названию

Популярные бренды