Kimberley KARAVAN 2021 Скачать руководство пользователя страница 31

Страница: 31 / 120

WiTi Wireless Trailer Plug Connection with built-in Anti-theft & GPS tracking (Optional)

OPERATION GUIDE

WiTi

Wireless Towing Interface replaces the traditional cables between a tow vehicle and caravan / trailer

with an advanced wireless connection.

WiTi

transmits all lighting and braking signals using the latest WiFi

technologies for fast, secure and stable communication. Although wireless,

WiTi

is not dependant upon

the Internet and communication is point to point between the vehicle unit and trailer unit. The signal is also

encrypted for security and other wireless devices will not interfere with the

WiTi

Wireless Towing Interface

(mobile phones, bluetooth, wifi devices, etc.)

No more cables to damage or rip out, no more corroded terminals and no more loose connections.

Low Power Mode

WiTi

Wireless Towing Interface will enter low power mode if there is inactivity for 24 hours. In this mode power

draw is less than 2 milliAmps.

WiTi

will exit Low Power Mode when it detects an input from the driving light

circuit.

CanBus and vehicles fi tted with advanced towing features

WiTi

Wireless Towing Interface supports all CanBus vehicles and vehicles with advanced electronics.

WiTi

supports vehicle specifi c towing modes and features for example, disabling reverse sensors when hitched.

These features will be enabled when the

WiTi

Wireless Towing Interface is in range and paired with the

WiTi

Anti Theft unit in the caravan or trailer. Please refer to your vehicle hand book for vehicle specifi c towing

modes.

WiTi

supports towing modes for:

• Dodge RAM

• Ford vehicles including F Series Trucks

• Isuzu

• Jeep

• Mitsubishi

• Nissan

• Toyota

• VW (Including Amarok and Toureg)

Supported Brake Controllers

WiTi supports all modern electric brake controllers including factory fi tted units on imported vehicles such as

Ford F Series and Dodge RAM.

If a

WiTi

Wireless Electric Brake Controller is installed then signals from wired brake controllers (pin 5) will be

ignored.

Your Kimberley has two recovery points in the rear. Always use a bridle /

equalizer strap for rear recovery, attach a shackle to each recovery point

and pull evenly from the middle.

Whilst these are suitable for winching/pulling from the rear under normal

conditions they are not designed for recovery of the Kimberley unit AND

the tow vehicle.

Rear Recovery Points

Kamper

Karavan

Kruiser

Locks & Keys

For your security and ease of use all Kimberley’s are supplied with regular & square-drive keys.

Types of keys;

1. Square-drive keys

2. Filler cap keys

Tail-gate latch keys (where fi tted)

It is recommend that these are kept in a secure but easy-to-access location .

RECOVERY

POINTS

SHACKLES

EQUALIZER

STRAP

SNATCH STRAP or WINCH CABLE

CAUTION!

When the conditions are diffi cult (up an incline; boggy; sand; deep ruts) you must recover the

Kimberley using the front hitch. Do not rely on the rear recovery points in these circumstances.

Содержание KARAVAN 2021

























































































































Результаты поиска

Содержание KARAVAN 2021

Отзывы:

Похожие инструкции для KARAVAN 2021

Бренды по названию

Популярные бренды

Kimberley KARAVAN 2021, Инструкция по установке, техническому обслуживанию и эксплуатации

Результаты поиска

Содержание KARAVAN 2021

Отзывы:

Похожие инструкции для KARAVAN 2021

Бренды по названию

Популярные бренды