background image

14

Universal Overhead Storage

Assembly Instructions

Assemble units as described herein only. To do otherwise 
may result in instability. All screws, nuts and bolts must be  
tightened securely and must be checked periodically after  
assembly. Failure to assemble properly, or to secure parts 
may result in assembly failure and personal injury.

3.  Place the fully assembled 

Universal overhead cabinet 

upside down onto a soft, 

protective surface (Figure 2).

4.  Position upmount brackets onto 

bottom of overhead so that the 

“point” of the v-notch aligns with 

the back of the overhead such 

that 

1

/

2

” overhangs the back of 

the cabinet, and the rectangular 

slot aligns with the side of the 

overhead. Align the adjacent face 

of the bracket with the end of the 

overhead such that 

1

/

4

” of bracket 

overhangs the side of the cabinet 

(Figure 2 & Detail E).

5. Using the correctly positioned 

upmount bracket as a template, 

mark the four mounting locations 

to the underside of the cabinet. 

Remove the bracket and drill 

four 

1

/

8

” diameter pilot holes 

into bottom ridge of the cabinet. 

Repeat the process for bracket at 

other side of cabinet (Detail F).

6. Align the correct upmount bracket 

with the pre-drilled holes of the 

cabinet and secure using four 

10 x 

1

/

2

” self-tapping screws. 

Repeat the process to secure the 

second bracket to other side of 

the cabinet (Figure 3).

Figure 2

upmount

bracket

(right-hand)

upmount

bracket

(left-hand)

Universal
overhead

cabinet

1

/ ”

2

1

/ ”

4

upmount

bracket

Universal

overhead cabinet

Detail E

v-notch

Detail F

mark for

pre-drill holes

v-notch

rectangular

slot

Figure 3

upmount

bracket

(right-hand)

upmount

bracket

(left-hand)

Universal
overhead

cabinet

10 x / ”

self-tapping

screws

1

2

Содержание Universal Overhead Storage

















Отзывы: