Ki Mobility Little Wave Clik Скачать руководство пользователя | Manualshive

Страница: 52 / 60

background image

51

One Arm Drive (OAD)

8. Install blade axles through axle mounts, wheels and handrims. Secure with washer and nut.

9. Level bearings by using the machined flat areas. Tighten bolts.

NOTE: If your chair has the 5th wheel option, continue with the instructions. If not, the assembly is
complete.

10. Install 5th wheel assembly as shown in the image below. The assembly slides onto the towers so that

they are mounted on the same towers as the one arm drive system, but just below those parts on the
towers. The two holes shown on the bar in the image below are used for mounting the Dynamic 5th
wheel option and face towards the back of the chair. A Standard 5th wheel option will have one hole
and face towards the back of the chair.

NOTE: In some chair configurations, new towers will be provided to add the additional length
needed to attach the one arm drive system. In that case, remove old tower and replace with new.
See next step if the new towers are needed.

Dynamic 5th
Wheel Holes

«
...
50
51
52
53
54
...
»

Содержание Little Wave Clik





























































Отзывы:

Нет отзывов

Похожие инструкции для Little Wave Clik

ICON BACK SYSTEM

Бренд: VARILITE Страницы: 20

Бренд: TA Service Страницы: 32

Comfort Classic

Бренд: ALCO Страницы: 15

Бренд: Arjohuntleigh Страницы: 48

Бренд: Meyra Страницы: 52

Бренд: Meyra Страницы: 44

Panda Futura 89539

Бренд: R82 Страницы: 6

Бренд: Vermeiren Страницы: 8

ROHO QUADTRO SELECT Series

Бренд: Permobil Страницы: 2

Бренд: AAT Страницы: 64

Бренд: AAT Страницы: 32

Бренд: Karman Страницы: 12

Бренд: Handicare Страницы: 4

Бренд: Quickie Страницы: 36

Бренд: Days Страницы: 18

LY-ESA120 HERO3

Бренд: Comfort Страницы: 32

Atlantis PR46068

Бренд: Able 2 Страницы: 2

ALLTRACK M3 Series

Бренд: LOGO SILVER Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды