Keysight 53210A Скачать руководство пользователя страница 231

Страница: 231 / 247

53210A Error Messages

Keysight 53210A User’s Guide

231

-128

Numeric data not allowed

A number was specified in the command header or in a parameter

where numeric data is not allowed.

-130

Suffix error

An error was detected in the suffix (units) of a numeric parameter,

but more specific information is not available.

-131

Invalid suffix

The parameter suffix is specified incorrectly
(e.g. 10 MZ rather than 10 MHZ).

-134

Suffix too long

A suffix contains more than 12 characters.

-138

Suffix not allowed

A suffix was specified for a numeric parameter when one is not

allowed.

-140

Character data error

A character error was detected in the command header or in a

parameter, but more specific information is not available.

-141

Invalid character data

Either an invalid character was received, or the character is not

valid for the command header.

-144

Character data too long

The character data contains more than 12 characters.

-148

Character data not allowed

A valid character was specified when another data type (numeric,

boolean) is required.

-150

String data error

An error was encountered in the string specified, but more specific

information is not available.

-151

Invalid string data

A required string parameter was received but is invalid.

-158

String data not allowed

A valid string was specified when another data type (numeric,

boolean) is required.

-160

Block data error

An error was encountered in the block data, but more specific

information is not available.

-161

Invalid block data

The number of bytes in a definite length data block does not match

the number of bytes indicated by the block header.

-168

Block data not allowed

A block data element was encountered at an instance where it is

not allowed by the instrument.

-170

Expression error

An error was encountered in a parameter expression, but more

specific information is not available.

-171

Invalid expression

The expression used to calculate a parameter value is invalid.

Table A-1

53210A Error Message Descriptions.

Code

Message

Description

Содержание 53210A
























































































































































































































































Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды

Keysight 53210A, Руководство пользователя

Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды