Keysight 53210A Скачать руководство пользователя страница 58

Страница: 58 / 247

53210A Software Installation and Interface Configuration

Keysight 53210A User’s Guide

Otherwise, continue with the ”Adding Instruments to the PC Interface” section of

this chapter.

Installing Instrument Drivers

Interchangeable Virtual Instrument (IVI) drivers (when available) are used for

programming the 53210A with Keysight VEE, with National Instruments®

LabVIEW™, or in Microsoft® development environments.
Install the appropriate driver based on the development environment you are

using (

Table 2-1

Accept all default directories specified during installation if

prompted. Setup type “Typical” is applicable for most users

Adding Instruments to the PC Interface

During installation of the Keysight IO Libraries, the IO interfaces (LAN, USB, GPIB)

detected on the

are configured. This section contains information for

programmatically adding the 53210A to those interfaces using the Keysight IO

Libraries ‘Connection Expert’ utility.
Simultaneous LAN/USB/GPIB connections to the instrument are allowed.

NOTE

Installing the Keysight IO Libraries installs the Interchangeable Virtual

Instrument (IVI) Shared Components. The IVI Shared Components are required

before

the IVI drivers (e.g. IVI-COM, IVI-C)can be installed.

NOTE

The figures used in this chapter represent the latest version of the IO Libraries

available at the time of printing. While you may have a different version, the

process of configuring and adding instruments remains basically the same.

Содержание 53210A
























































































































































































































































Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды

Keysight 53210A, Руководство пользователя

Результаты поиска

Содержание 53210A

Отзывы:

Похожие инструкции для 53210A

Бренды по названию

Популярные бренды