Keysight Technologies PD1000A Скачать руководство пользователя | Manualshive

Страница: 30 / 44

background image

30

Keysight PD1000A Test Fixture Operating Guide

Customizing an SMD Test Fixture

Customizing an SMD Test Fixture

The SMD Test Fixture and as provided by Keysight is suitable for TO-263 seven

pin SMD devices. These devices must have Pin 1 connected to the Gate of the

device under test. The device Tab must connect to the Drain or Collector. The

Source or Emitter pin(s) must connect to GND.

Figure 16 shows the primary components of the SMD Test Fixture. Refer to the

following instructions.

IMPORTANT:

Because each SMD devices is unique, the customer is

required to create and assemble a PC board, frame guide, and

Calibration Standards specific to the device(s) they intend to test.

This section provides general guidelines to customize the SMD

test fixture.
Detailed CAD files (.dxf) for the PC Board, the Frame Guide and

Calibration Standards for standard MOSFET and IGBT devices are

available as part of the PD1000A installation.
You will also need to purchase a Keysight Frame.

Figure 17

PD1000A SMD Test Fixture Components

Keysight Frame with

SMA Connectors.

User lays-out and provides microstrip

PC Board with device contact pattern.

User designs and provides

Frame Guide to place SMD.

Vertically Conductive

sheet.

«
...
28
29
30
31
32
...
»

Содержание PD1000A













































Отзывы:

Нет отзывов

Похожие инструкции для PD1000A

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: jenway Страницы: 50

Бренд: jenway Страницы: 62

Бренд: Yamaha Страницы: 6

Бренд: CA.MI Страницы: 68

Бренд: Feature tech Страницы: 2

Бренд: Bogen Страницы: 14

Бренд: Kurzweil Страницы: 12

Бренд: Lumel Страницы: 40

LiveTester LT 220

Бренд: StarLogixs Страницы: 7

Бренд: Hameg Страницы: 40

MultiScanner HD800 OneStep

Бренд: Zircon Страницы: 2

Бренд: HERON Страницы: 2

Бренд: BERG Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды