Keysight Technologies PD1000A Скачать руководство пользователя

Страница: 5 / 44

Safety Symbols and Notices

A CAUTION denotes a hazard. It

calls attention to an operating pro-

cedure or practice that, if not cor-

rectly performed or adhered to,

could result in damage to the

product or loss of important data.

Do not proceed beyond a CAUTION

notice until the indicated condi-

tions are fully understood and met.

A WARNING denotes a hazard. It

calls attention to an operating pro-

cedure or practice, that, if not cor-

rectly performed or adhered to,

could result in personal injury or

death. Do not proceed beyond a

WARNING notice until the indi-

cated conditions are fully under-

stood and met.

Products display the following sym-

bols:

Indicates that antistatic

precautions should be

taken.

Electro-Magnetic Compatibility (EMC) Information

The Test Solution is sensitive to electro-magnetic disturbances in the frequency range of 80 MHz to 6 GHz.

To minimize the risk of incorrect measurements avoid intentional radiators in close proximity to the Test Solution.

Содержание PD1000A













































Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды

Keysight Technologies PD1000A, Руководство по эксплуатации

Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды