Keysight Technologies PD1000A Скачать руководство пользователя

Страница: 4 / 44

Safety Information

The following general safety precau-

tions must be observed during all

phases of operation of these instru-

ments. Failure to comply with these

precautions or with specific warnings

or operating instructions in the product

manuals violates safety standards of

design, manufacture, and intended use

of the instruments. Keysight Technolo-

gies assumes no liability for the cus-

tomer's failure to comply with these

requirements.

General

Do not use these instruments in any manner

not specified by the manufacturer. The pro-

tective features of these instruments must

not be impaired if it is used in a manner

specified in the operation instructions.

Before Applying Power

Verify that all safety precautions are taken.

Make all connections to the instruments

before applying power. Note the external

markings described under “Safety Symbols”.

Ground the Instrument

Keysight instruments are provided with

a grounding-type power plug. The

instruments must be connected to an

electrical ground to minimize shock

hazard. The ground pin must be firmly

connected to an electrical ground

(safety ground) terminal at the power

outlet. Any interruption of the protec-

tive (grounding) conductor or discon-

nection of the protective earth terminal

will cause a potential shock hazard

that could result in personal injury.
Unless otherwise noted in the specifi-

cations, these instruments or system is

intended for indoor use in an installa-

tion category II, pollution degree 2

environment per IEC 61010-1 and 664

respectively. They are designed to

operate at a maximum relative humid-

ity of 5% to 80% at 40 °C or less (non-

condensing). These instruments or sys-

tem are designed to operate at alti-

tudes up to 3000 meters, and at

temperatures between 0 and 55 °C.Do

Not Operate in an Explosive Atmo-

sphere Do not operate in the presence

of flammable gases or fumes.

Do Not Operate Near Flammable

Liquids

Do not operate the instruments in the

presence of flammable liquids or near

containers of such liquids.

Cleaning

Clean the outside of the Keysight

instruments with a soft, lint-free,

slightly dampened cloth. Do not use

detergent or chemical solvents.

Do Not Remove Instrument Cover

Only qualified, service-trained person-

nel who are aware of the hazards

involved should remove instrument

covers. Always disconnect the power

cable and any external circuits before

removing the instrument cover.

Keep away from live circuits

Operating personnel must not remove

equipment covers or shields. Proce-

dures involving the removal of covers

and shields are for use by service-

trained personnel only. Under certain

conditions, dangerous voltages may

exist even with the equipment

switched off. To avoid dangerous elec-

trical shock, DO NOT perform proce-

dures involving cover or shield removal

unless you are qualified to do so.

DO NOT operate damaged

equipment

Whenever it is possible that the safety

protection features built into these

instruments have been impaired, either

through physical damage, excessive

moisture, or any other reason,

REMOVE POWER and do not use the

instrument until safe operation can be

verified by service-trained personnel. If

necessary, return the product to a Key-

sight Technologies Sales and Service

Office for service and repair to ensure

the safety features are maintained.

DO NOT block the primary

disconnect

The primary disconnect device is the

appliance connector/power cord when

an instrument used by itself, but when

installed into a rack or system the dis-

connect may be impaired and must be

considered part of the installation.

Do Not Modify the Instrument

Do not install substitute parts or per-

form any unauthorized modification to

the product. Return the product to a

Keysight Sales and Service Office to

ensure that safety features are main-

tained.

In Case of Damage

Instruments that appear damaged or

defective should be made inoperative

and secured against unintended oper-

ation until they can be repaired by

qualified service personnel.

Measurement Limits

The Truevolt Series DMMs provide pro-

tection circuitry to prevent damage to

the instrument and to protect against

the danger of electric shock, provided

the Measurement Limits are not

exceeded. To ensure safe operation of

the instrument, do not exceed the

Measurement Limits shown on the

front and rear panel.
The DMMs comply with EN/IEC 61326-

2-1, for sensitive test and measure-

ment equipment.
When subjected to transient radiated

and/or conducted electromagnetic

phenomena, the DMMs may have tem-

porary loss of function or performance

which is self-recovering. Recovery may

take longer than 10 seconds.
When subjected to continuously pres-

ent electromagnetic phenomena, some

degradation of performance may

occur.

Содержание PD1000A













































Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды

Keysight Technologies PD1000A, Руководство по эксплуатации

Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды