Keysight Technologies PD1000A Скачать руководство пользователя

Страница: 9 / 44

PD1000A Test Fixtures

Operating Guide

General Information

Keysight’s PD1000A Power Device Measurement System for Advanced Modeling

System option -SPK Accessory Kit provides three device test fixtures:

–

One for 3-terminal devices with TO-220 style packages (Keysight p/n.

PD1000-67900).

–

One for 3-terminal devices with TO-247 style packages (Keysight p/n.

PD1000-67901).

–

One for Surface Mount Devices (SMD) with 7-pin TO-263 packages

(Keysight p/n. PD1000-67902).

This accessory kit is used for making S-Parameter measurements.

Incoming Inspection

After unpacking the Test Fixture(s), carefully inspect them for any shipping

damage. Report any damage to the shipping agent immediately, as such

damage is not covered by the warranty.

Returning for Service

If you need to return a test fixture for service, attach a tag indicating the type of

service required, your return address, and model number of the device to be

repaired.
Repackaging the device requires original shipping containers and materials or

their equivalents. Keysight Technologies can provide packaging materials

identical to the original materials. Contact Keysight as per

“Sales and Technical

Support”

in the front matter of this manual.

Preparation for Use

The PD1000A Test Fixtures connect the device to be tested (DUT) to the Bias T

Networks. Refer to Figure 1 on page 12 for a typical test setup.

Licensing is required to use the PD1000A Power Device

Measurement System Control Software for making On State and

Off State S-Parameter measurement. Refer to the PD1000A

Startup Guide for licensing information.

Содержание PD1000A













































Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды

Keysight Technologies PD1000A, Руководство по эксплуатации

Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды