Keysight Technologies PD1000A Скачать руководство пользователя

Страница: 41 / 44

Keysight PD1000A Power Device Measurement System

Use Proper SMA Connector Care and Connection Techniques

Hold the torque wrench lightly, at the end of the handle only (beyond the

groove). See the following figure.

Apply force downward to the wrench handle. This applies torque to the

connection through the wrench. Do not hold the wrench so tightly that you

push the handle straight down along its length rather than pivoting it,

otherwise you apply an unknown amount of torque.

Tighten the connection just to the torque wrench break point. The wrench

handle gives way at its internal pivot point. Do not tighten the connection

further.

Separating Connections

To avoid lateral (bending) force on the connector mating plane surfaces, always

support the devices and connections.

Use an open-end wrench or spanner wrench to prevent the device body from

turning.

Use another open-end wrench or the torque wrench to loosen the connector

nut.

Complete the separation by hand, turning only the connector nut.

Pull the connectors straight apart without twisting, rocking, or bending.

Figure 9

Using the Torque Wrench

Torquing Direction

Stop when handle begins to yield

You don’t have to fully break the handle of the torque wrench to

reach the specified torque; doing so can cause the handle to kick

back and loosen the connection. Any give at all in the handle is

sufficient torque.

not

turn the device body. Only turn the connector nut. Damage

to the center conductor can occur if the device body is twisted.

Содержание PD1000A













































Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды

Keysight Technologies PD1000A, Руководство по эксплуатации

Результаты поиска

Содержание PD1000A

Отзывы:

Похожие инструкции для PD1000A

Бренды по названию

Популярные бренды