Keysight Technologies PD1000A Скачать руководство пользователя | Manualshive

Страница: 29 / 44

background image

Keysight PD1000A Test Fixture Operating Guide

29

Inserting the Cal Standards into the PD1000A SMD Test Fixture

Inserting the Cal Standards into the PD1000A SMD Test Fixture

Use the Test Fixture PC Board, Vertically Conductive Sheet, and Frame Guide

supplied with the SMD Test Fixture for fixture calibration.
Inserting Calibration Standards into the Test Fixture is the same as inserting your

device to be tested. This section shows the orientation of the Calibration

Standards inserted into the Test Fixture.

Important:

Notice the orientation of the standards, see Figure 16

below. Insert all seven Calibration Standards with the same

orientation.

Figure 16

Placing an

OPEN

,

SHORT

, or

LOAD

Standard into the SMD Test Fixture

«
...
27
28
29
30
31
...
»

Содержание PD1000A













































Отзывы:

Нет отзывов

Похожие инструкции для PD1000A

Бренд: ABB Страницы: 20

Бренд: Utilitech Страницы: 2

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: IEI Technology Страницы: 85

Бренд: TC Electronic Страницы: 20

Бренд: Hammond Страницы: 78

Бренд: Keithley Страницы: 343

Бренд: Keithley Страницы: 334

Бренд: La Crosse Technology Страницы: 2

Бренд: Yamaha Страницы: 31

Бренд: AEMC Страницы: 4

Бренд: DAKOTA ULTRASONICS Страницы: 38

Бренд: Palstar Страницы: 37

Бренд: LD Didactic Страницы: 2

Бренд: LEGRAND Страницы: 5

Digital Piano CA750

Бренд: Kawai Страницы: 76

Бренд: CAS Corporation Страницы: 20

Бренд: Tektronix Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды