Keysight Technologies N5241AU-922 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 42

background image

14 Installation Note N5242-90003

Description of the Upgrade
Installation Procedure for the Upgrade

-

4.

Disconnect the front panel interface ribbon cable (item

③

). The front panel

is now free from the analyzer.

Figure 3

Front Panel Assembly Removal

Step 5. Remove the Existing Test Set Cables

Refer to

for this step of the procedure.

1.

Place the analyzer bottom-side up on a flat surface.

2.

Remove the following cables in the order listed:

— W4A25 port 1 bridge to W3 (from A5 26.5 GHz source 1 board OUT 1)
— W10A28 port 2 bridge to W9 (from A5 26.5 GHz source 1 board OUT 2)
— W40Front-panel REF 2 RCVR R2 IN to A23 mixer brick (R2)

Leave the gray flexible cables, the wire harnesses, and the ribbon cables

connected where possible. Any that are removed should be labeled for

reconnection later.

Be careful not to damage the center pins of the semirigid cables. Some

flexing of the cables may be necessary but do not over-bend them.

«
...
12
13
14
15
16
...
»

Содержание N5241AU-922











































Отзывы:

Нет отзывов

Похожие инструкции для N5241AU-922

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

CP-4900 Micro-GC

Бренд: Varian Страницы: 7

Бренд: Vapotherm Страницы: 2

Бренд: Abus Страницы: 168

Бренд: OHAUS Страницы: 76

Бренд: Van Walt Страницы: 2

Бренд: Power Measurement Страницы: 20

Бренд: Feature tech Страницы: 2

Бренд: Hanna Instruments Страницы: 12

Бренд: Aalborg Страницы: 56

Бренд: Stabila Страницы: 14

AERASGARD FSFTM-CO2-Modbus Series

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Zensol Страницы: 12

Бренд: R&S Страницы: 100

Бренд: Seli Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды