Keysight Technologies N5241AU-922 Скачать руководство пользователя страница 37

Страница: 37 / 42

Installation Note N5242-90003 37

Description of the Upgrade
Installation Procedure for the Upgrade

— A keyboard must be connected to the network analyzer.

Option Enable Procedure

1. To start the option enable utility, press UTILITY

, then

then

. An option enable dialog box will appear.

Click the arrow in the Select Desired Option box. A list of available options

will appear.

In the Select Desired Option list, click

224 - 2nd Src w/Combiner &

Switches

Using the keyboard, enter the license key in the box provided. The license

key is printed on the license message you received from Keysight. Enter

this key exactly as it is printed on the message.

Click Enable.

Click Yes in answer to the displayed question in the Restart Analyzer? box.

When the installation is complete, click Exit.

Option Verification Procedure

Once the analyzer has restarted and the Network Analyzer program is again

running:
1.

On the analyzer’s Help menu, click About Network Analyzer.

Verify that “224” is listed after “Options:” in the display. Click OK.

System

Service

Option Enable

If Option 224 has not been enabled, contact Keysight Technologies. Refer

“Getting Assistance from Keysight” on page 4

Содержание N5241AU-922











































Результаты поиска

Содержание N5241AU-922

Отзывы:

Похожие инструкции для N5241AU-922

Бренды по названию

Популярные бренды

Keysight Technologies N5241AU-922, Руководство пользователя

Результаты поиска

Содержание N5241AU-922

Отзывы:

Похожие инструкции для N5241AU-922

Бренды по названию

Популярные бренды