Keysight Technologies N5241AU-922 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 42

background image

10 Installation Note N5242-90003

Description of the Upgrade
Installation Procedure for the Upgrade

-

Installation Procedure for the Upgrade

The network analyzer must be in proper working condition prior to installing

this option. Any necessary repairs must be made before proceeding with this
installation.

Overview of the Installation Procedure

“Step 1. Obtain a Keyword and Verify the Information.”
“Step 2. Remove the Outer Cover.”
“Step 3. Remove the Inner Cover.”
“Step 4. Remove the Front Panel Assembly.”
“Step 5. Remove the Existing Test Set Cables.”
“Step 6. Assemble the Mechanical Switches.”
“Step 7. Install the Mechanical Switches.”
“Step 8. Install the Second Source Boards.”
“Step 9. Install the Source 2 Front Panel Connectors.”
“Step 10. Remove the A19 Test Set Motherboard and the A20 IF Multiplexer

Board.”
“Step 11. Install the Bulkhead Connectors and Jumpers on the Rear Panel.”
“Step 12. Install the Bulkhead Connectors in the Test Set Front Plate.”
“Step 13. Install the New Test Set Cables.”
“Step 14. Reinstall the A20 IF Multiplexer Board and the A19 Test Set

Motherboard.”
“Step 15. Replace the Lower Front Panel Overlay.”
“Step 16. Reinstall the Front Panel Assembly and Front Panel Jumpers.”
“Step 17. Position the Cables and Wires to Prevent Pinching.”
“Step 18. Reinstall the Inner Cover.”
“Step 19. Reinstall the Outer Cover.”
“Step 20. Enable Option 224.”
“Step 22. Perform Post-Upgrade Adjustments and Calibration.”
“Step 23. Prepare the PNA for the User.”

This installation requires the removal of the analyzer’s protective

outer covers. The analyzer must be powered down and

disconnected from the mains supply before performing this

procedure.

«
...
8
9
10
11
12
...
»

Содержание N5241AU-922











































Отзывы:

Нет отзывов

Похожие инструкции для N5241AU-922

Бренд: E Instruments Страницы: 2

Бренд: IFM Страницы: 2

Бренд: Maico Страницы: 27

Бренд: Magnescale Страницы: 14

Бренд: WATERGUARD Страницы: 2

Бренд: Nagano Keiki Страницы: 25

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

LaserDIMENSIONMASTER 3336

Бренд: Calculated Industries Страницы: 2

Бренд: Major tech Страницы: 16

Бренд: YOSensi Страницы: 27

Бренд: Scheppach Страницы: 20

Бренд: Barco Страницы: 33

Multimar 25 EWR

Бренд: Mahr Страницы: 20

Бренд: ZETA Music Systems Страницы: 10

Бренд: TESTO Страницы: 2

Бренд: AlazarTech Страницы: 60

Бренд: Kobold Страницы: 12

Бренд: PKP Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды