Keysight Technologies N2797A Скачать руководство пользователя страница 44

Страница: 44 / 48

N2797A User’s Guide

Performance Verification

Figure 19

Forward and Reverse Setup

Press the

transmission

screen key.

Press the

do both fwd and reverse

screen key.

Wait until the VNA beeps four times indicating that it has completed the task.

Press the

isolation

screen key.

Press the

omit isolation

screen key.

Press

done 2 port cal

screen key.

Set the VNA's averaging to off.

Save the reference plane cal by pressing the

[save recall]

key then the

[save state]

key.

You may change name if you wish.

Press the

[scale reference]

key. Then set the scale to 1 dB per division and the reference

position for 7 divisions.

Set reference value for 0 dB.

Press the

[measure]

key.

Press the

s21

screen key.

Ensure s21 response on screen is flat out to 1.5 GHz.

Содержание N2797A

















































Результаты поиска

Содержание N2797A

Отзывы:

Похожие инструкции для N2797A

Бренды по названию

Популярные бренды

Keysight Technologies N2797A, Руководство пользователя

Результаты поиска

Содержание N2797A

Отзывы:

Похожие инструкции для N2797A

Бренды по названию

Популярные бренды