Keysight Technologies N2797A Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 48

background image

28

N2797A User’s Guide

2

Probe Calibration

Calibrating the Probe on Infiniium Oscilloscopes

Probe calibrations vary slightly between series 9000, 90000, and 90000 X oscilloscopes. For

9000 series oscilloscopes, the following calibrations are used:
• Skew Calibration
• Attenuation/Offset Calibration

For 90000 series oscilloscopes, the following calibrations are used:
• DC Attenuation/Offset Calibration
• Skew Calibration

When performing a the skew calibration, the E2655B Performance Verification (PV) and

deskew fixture is used. The PV fixture is included with the Deskew Kit which is shipped with

Infiniium oscilloscopes. The fixture is also used in the performance verification procedure

that is documented in

, “Performance Verification".

An optional N2787A 3D Probe Positioner or equivalent can be used to hold

the probe during the calibration.

Procedure

1

Turn on the oscilloscope. Allow the oscilloscope and probe to warm up for 20 minutes

before performing the probe calibrations.

2

If the oscilloscope needs calibration, perform a user calibration before the probe

calibration. On the oscilloscope, click

Utilities > Calibration

.

3

On the oscilloscope, click

Setup > Probes

.

4

In the Probe Calibration dialog box, select the tab representing the channel that has the

probe attached.

5

In the dialog box, select the probe head and the type of calibration. Click

Start

and follow

the instructions shown on the oscilloscope.

6

When performing the skew calibration, you will be instructed to use the PV fixture. Observe

these points:
• Connect the PV fixture’s input to the oscilloscope’s calibration output as shown in

on page 29. Connect a 50 ohm terminator to the PV’s output.

«
...
26
27
28
29
30
...
»

Содержание N2797A

















































Отзывы:

Нет отзывов

Похожие инструкции для N2797A

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

Бренд: Ebtron Страницы: 5

Бренд: Okolab Страницы: 4

Бренд: jablotron Страницы: 2

Бренд: La Crosse Technology Страницы: 8

Бренд: Energometrika Страницы: 39

Бренд: Conrad Electronic Страницы: 38

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

Бренд: Omega Страницы: 20

miniSERIES Series

Бренд: Valeport Страницы: 25

Seeker 400 Series

Бренд: General Страницы: 24

Бренд: shelyak Страницы: 45

Бренд: RS PRO Страницы: 41

Бренд: 3M Страницы: 168

Бренд: Z-TRAUQ Страницы: 10

Бренд: SIGRIST Страницы: 84

Alyza IQ PO4-XYZ

Бренд: Xylem Страницы: 172

Бренд: Vaisala Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды