Keysight Technologies N2797A Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 48

background image

24

N2797A User’s Guide

1

Using the Probe

Safety Information

To avoid personal injury and to prevent fire or damage to this product or products

connected to it, review and comply with the following safety precautions. Be aware that if

you use this probe assembly in a manner not specified, the protection this product provides

may be impaired.

WARNING

Handle the probe with care to avoid injury, especially when it is fitted with the sharp spring or rigid tip.

WARNING

Handle Probe Tips and Accessories Carefully. Some of the probe tips and accessories are very sharp
(the browser tips, for example). You should handle these with care to avoid personal injury.

WARNING

Use Only Grounded Instruments. Do not connect the probe’s ground lead to a potential other than earth
ground. Always make sure the probe and the oscilloscope are grounded properly.

WARNING

Connect and Disconnect Properly. Connect the probe to the oscilloscope and connect the ground lead
to earth ground before connecting the probe to the circuit under test. Disconnect the probe input and
the probe ground lead from the circuit under test before disconnecting the probe from the
oscilloscope.

WARNING

Observe Probe Ratings. Do not apply any electrical potential to the probe input which exceeds the
maximum rating of the probe. Make sure to comply with the voltage versus frequency derating curve
found in this manual.

WARNING

Keep Away From Live Circuits. Avoid open circuitry. Do not touch connections or components when
power is present.

«
...
22
23
24
25
26
...
»

Содержание N2797A

















































Отзывы:

Нет отзывов

Похожие инструкции для N2797A

Бренд: Kawai Страницы: 5

Бренд: Jata hogar Страницы: 12

Бренд: HANYOUNG NUX Страницы: 4

Бренд: jenway Страницы: 30

Бренд: National Meter & Automation Страницы: 24

Бренд: Lakeshore Страницы: 2

Бренд: Kamstrup Страницы: 4

Бренд: HANYOUNGNUX Страницы: 4

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: Larson Davis Страницы: 536

Бренд: Underground Magnetics Страницы: 48

Бренд: BD Sensors Страницы: 4

Бренд: Roland Страницы: 2

Бренд: Karman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды