Keysight Technologies E8364-60108 Скачать руководство пользователя страница 9

Страница: 9 / 32

6 Keysight E8363B/C and E8364B/C Installation Note

General Information
Installation Procedure for the Upgrade Kit

Step 3. Raise the Receiver Deck.

Step 4. Remove the Existing Cables.

Step 5. Install the Attenuators and Bias Tees.

Step 6. Install the Option UNL Cables.

Step 7. Lower and Fasten the Receiver Deck and Connect the Bias Tee Control Cables.

Step 8. Replace the Lower Front Panel Overlay (Option 014 Only).

Step 9. Reinstall the Front Panel Assembly and Front Panel Jumpers (Option 014 Only).

Step 10. Reinstall the Outer Cover.

Step 11. Enable Option UNL.

Step 12. Perform Post-Upgrade Adjustments and Calibration.

Tools and Equipment Required for the Installation

Equipment Required for Post-Upgrade Adjustments

Description

Qty

Part Number

T-8 TORX driver (set to 5 in-lbs)

N/A

T-10 TORX driver (set to 9 in-lbs)

N/A

T-20 TORX driver (set to 21 in-lbs)

N/A

5/16-inch torque wrench (set to 10 in-lbs)

N/A

5/16-inch torque wrench (set to 21 in-lbs) (Option 014 only)

N/A

ESD grounding wrist strap

9300-1367

5-ft grounding cord for wrist strap

9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire

9300-0797

ESD heel strap (for use with conductive floors)

9300-1308

Use a 5/16-inch torque wrench set to 10 in-lbs on all cable connections

except the front-panel connectors to which the front-panel jumpers attach

(Option 014). Use a 5/16-inch torque wrench set to 21 in-lbs for these

connections.

Equipment Type

Model or

Part Number

Alternate Model or Part

Number

Power meter

E4418B/E4419B

E4418A/E4419A

Power sensor, 2.4 mm

8487A

None

Adapter, 2.4 mm (f) to 2.4 mm (f)

11900B

85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f)

85133C

85133E

Содержание E8364-60108

































Результаты поиска

Содержание E8364-60108

Отзывы:

Похожие инструкции для E8364-60108

Бренды по названию

Популярные бренды

Keysight Technologies E8364-60108, Установочная инструкция

Результаты поиска

Содержание E8364-60108

Отзывы:

Похожие инструкции для E8364-60108

Бренды по названию

Популярные бренды