Kentrox RMM-1400 Скачать руководство пользователя | Manualshive

Страница: 6 / 246

background image

Remote RMM-1400 Version 2.0x Configuration Guide

About this Document: Cautions and Warnings

iv

Cautions and Warnings

Electrostatic Discharge Caution

CAUTION:

Kentrox equipment and its peripherals contain electrostatic sensitive
components. Proper handling, shipping, and storage precautions must
be exercised:



You must remove and install cards in a static-free environment. Wear
an antistatic wrist strap that is plugged into the Kentrox equipment so
you are grounded at the same point as the equipment.



Do not remove cards from their antistatic plastic bags until you are
ready to install them into the chassis.



Immediately after you remove a card from the chassis, you must
insert it into its antistatic bag.



When the cards are not in use, keep them in their antistatic plastic
bags.



Do not ship or store cards near strong electrostatic, electromagnetic,
or radioactive fields.

Ground Caution

CAUTION:

For Kentrox equipment to operate safely and correctly, there must be a
safety ground strap between the equipment ground bolts and the office
ground.

FCC Warning

The Federal Communications Commission has set limits for emitted radio
interference, and Remote RMM-1400 is constructed with this electromagnetic
interference (EMI) limitation in mind. Remote RMM-1400 is classified under FCC
regulations as a Class A device, that is, a device for use in commercial environments
and not in residential areas. This device has been tested and shown to comply with
the following FCC rule: Part 15 Subpart J. Operation of this equipment in a residential
area may cause interference to radio and TV reception, requiring the user to take
whatever steps are necessary to correct the interference.

Information is available from the FCC describing possible corrective actions. To
maintain low EMI levels, we suggest that you use only metal connectors and shielded
cable grounded to the frame.

Specifications are subject to change without notice.

«
...
4
5
6
7
8
...
»

Содержание RMM-1400























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RMM-1400

Бренд: IBM Страницы: 342

MatrixPRO-II DVI 16x16

Бренд: Barco Страницы: 43

Бренд: Barco Страницы: 5

Бренд: Nayar Systems Страницы: 37

Бренд: N-Tron Страницы: 62

Patton SmartNode 2300 Series

Бренд: Patton electronics Страницы: 2

Бренд: Paradyne Страницы: 12

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: Xilica Audio Design Страницы: 30

Бренд: Mitsubishi Страницы: 874

Бренд: Mellanox Technologies Страницы: 57

HHM Series HHM2245SA1

Бренд: TDK Страницы: 2

Бренд: Disc Makers Страницы: 38

Бренд: Perle Страницы: 491

Бренд: IBM Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды