manualshive.com logo in svg

Kentrox RMM-1400, Руководство по настройке

Поделиться
Скачать
Kentrox RMM-1400 Скачать руководство пользователя страница 176

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the SNMP Proxy: Configuring a Mediation SNMP Measurement Template

17-12

6. Configure the varbind-match 

.1.3.6.1.4.1.539.42.2.2.1.1 

for the 

critical

 

state; that is, the OID to use to retrieve the value of 

$alIndex

:

config mediation snmp measurement-template alDef trap critical 

varbind-match .1.3.6.1.4.1.539.42.2.2.1.1 $alIndex

7. Configure a varbind value of for 

.1.3.6.1.4.1.539.42.2.2.1.5

 for the 

critical

 state:

config mediation snmp measurement-template alDef trap critical 

varbind-value .1.3.6.1.4.1.539.42.2.2.1.5

8. Configure the template 

alDef

 to consider as significant the second numeric value 

in a string response for 

critical

 traps:

config mediation snmp measurement-template alDef trap critical 

value-match 2

9. (optional) Verify that the point template has been configured properly:

show mediation snmp measurement-templates alDef

The command response appears similar to the following:

10. Save the configuration.

To configure a mediation SNMP measurement template that configures a group of 
measurements:

1. Configure the point template name 

alTableDef

:

config mediation snmp measurement-template alTableDef

2. (optional) Configure an associated description 

Measurement group

:

config mediation snmp measurement-template alTableDef description 

Measurement group

(Dub)>show mediation snmp measurement-templates alDef
Name: alDef
Description: Single measurement
Poll OID: .1.3.6.1.4.1.539.42.2.2.1.5.$(alIndex)
Value Match Index: 2
Value Conversion Multiplier: 1
Trap: critical
    Trap OID: .1.3.6.1.4.1.539.42.2.0.5
    Varbind Value: .1.3.6.1.4.1.539.42.2.2.1.5
    Value Match Index: 2
    Varbind Match: .1.3.6.1.4.1.539.42.2.2.1.1 = $alIndex
(Dub)>

Содержание RMM-1400























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды