Kentrox RMM-1400 Скачать руководство пользователя

Страница: 179 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the SNMP Proxy: Configuring a Mediation SNMP Network Element

17-15

Configuring a Mediation SNMP Network Element

To configure a mediation SNMP NE:

1. Configure the name,

ProxyNE

for the mediation SNMP NE:

config mediation snmpne ProxyNE

2. Configure the network element name,

ProxyNE

config mediation snmpne ProxyNE ne-name ProxyNE

3. Configure the host with an IP address of

10.40.65.90

, port number

161

community name

administrator

, and SNMP version number

. These

parameters are used for polling the device.

config mediation snmpne ProxyNE host 10.40.65.90 161 administrator

4. Configure the category as

NECategory

config mediation snmpne ProxyNE category NECategory

5. Configure status point

ethernet1

with

a link to the previously defined

ifEntryDef

point template, a replaceable parameter name

ifIndex

, and a value

for that parameter as

config mediation snmpne ProxyNE point ethernet1 ifEntryDef ifIndex

6. Configure status point

ethernet2

with

a link to the previously defined

ifEntryDef

point template, a replaceable parameter name

ifIndex

, and a value

for that parameter as

config mediation snmpne ProxyNE point ethernet2 ifEntryDef ifIndex

7. Configure an event named

reboot

with a link to the previously defined

coldStartDef

event template:

config mediation snmpne ProxyNE event reboot coldStartDef

In this scenario, you will configure information specific to a mediation SNMP NE
including:



The host parameters



A link to the previously defined event template,

coldStartDef

which defines

the associated event



A link to the previously defined point template,

ifEntryDef

which defines the

associated event



A link to the previously defined measurement template,

alTableDef

, which

defines a means of obtaining a value for a point on a proxied NE.

Содержание RMM-1400






















































































































































































































































Результаты поиска

Содержание RMM-1400

Отзывы:

Похожие инструкции для RMM-1400

Бренды по названию

Популярные бренды

Kentrox RMM-1400, Руководство по настройке

Результаты поиска

Содержание RMM-1400

Отзывы:

Похожие инструкции для RMM-1400

Бренды по названию

Популярные бренды