manualshive.com logo in svg

Kentrox RMM-1400, Руководство по настройке

Поделиться
Скачать
Kentrox RMM-1400 Скачать руководство пользователя страница 152

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring the Peripheral Management Subsystem: Expansion Peripheral States

16-6

Initializing

Specifies that Remote RMM-1400 has established a 
management connection to the peripheral and is 
exchanging initial setup messages with it.

IncompatibleManaged

Specifies that the following conditions exist:

Remote RMM-1400 has successfully set up and 
initialized a management connection to the 
peripheral.

The peripheral’s firmware is incompatible with 
Remote RMM-1400’s firmware.

Remote RMM-1400 is not currently downloading 
compatible firmware to the peripheral (and perhaps 
cannot, for some reason).

When a peripheral is in this state, only basic peripheral 
management functions are available, such as updating 
the image and reloading.

Downloading

Specifies that Remote RMM-1400 is downloading a new 
firmware image to the peripheral.

Managed

Specifies that Remote RMM-1400 has successfully set 
up and initialized a management connection to the 
peripheral.

Online

Specifies that the peripheral is fully operational. Remote 
RMM-1400 has established a management connection 
to it and it is fully functioning as part of Remote RMM-
1400.

Table 16-2   Potential Expansion Peripheral Operation States (Continued)

Operation State

Description

Содержание RMM-1400























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды