manualshive.com logo in svg

Kentrox RMM-1400, Руководство по настройке

Поделиться
Скачать
Kentrox RMM-1400 Скачать руководство пользователя страница 227

Glossary-15

 Glossary

keep-alive packets

Keep-alive packets are sent from both the client and server when no user data is 
being transmitted. When one side of the connection fails to receive packets, a 
notification is sent to indicate a disconnected peer. These packets also maintain an 
active firewall state.

L

LCP echo request

An LCP echo request is a packet sent from a client-side controller to a server-side 
controller to signal if a PPP link is still available. PPPD stops if LCP echo requests are 
not received by the server. LCP echo requests are sent only if LCP is enabled.

line buildout

Line buildout refers to the length of the cable (in feet) that is connecting the devices 
on each end of a T1 line or the level of attenuation (in decibels) required for the 
devices on each end of a T1 line to communicate. Buildout is usually specified by 
cable length for shorter connections and by level of attenuation for longer 
connections.

linemode

Linemode is the type of hardware connection of an asynchronous link. There are two 
values for linemode: RS232 and RS422. RS232 is a set of standards that specify the 
type of interfaces connected to an asynchronous controller. The three types of 
interfaces are electrical, functional, and mechanical, which are used for 
communicating to computers, terminals, and modems. RS422 is a standard that 
defines a balanced interface that does not accompany a physical connector.

local identity

The local identity is supplied by the local site and sent to a remote device. The identity 
is similar to a user name for CHAP and PAP authentication on a point-to-point 
connection.

Содержание RMM-1400























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды